MarineKinetix MK4+ Скачать руководство пользователя страница 17

Страница: 17 / 19

MK4+ Hybrid Charge Controller User Manual

6. Troubleshooting

If your phenomenon is not included in the above descriptions, please contact MarineKinetix or
your dealer for assistance.

7. Installation Environment

Avoid operating the apparatus under direct sunshine, blazing sun, and rainy, moist, or

acid mist environments, etc.

Keep the apparatus away from flammable and explosive gas or hazard, including

flame and spark.

Problem

Possible Cause and Solution

Symbol flashing, no charge or

discharge.

Battery is over-voltage, check battery voltage, and whether

the cables are well-connected. Re-connect all components.

Symbol flashing and no output.

Battery is over-discharged or dead. Fully recharge it with a

shore-base charger if the battery is fully discharged.

Generator based chargers should never be used to recharge

a fully depleted battery bank. This includes engine

alternators.

Symbol flashing and no output.

Your output #1 or #2 are in overload. Please check the load,

and remove the extra load, then press "Esc" button to

recover.

Symbol flashing and no

output.

Short-circuit. Check the all wiring, and remove the

short-circuit hazard or damaged load, then press "Esc" button

to recover.

No LCD display.

1. LCD wire connection might be loose, please open

controller case to check.

2. The fuse might be burnt due to the battery reverse

connection, please open controller case to check.

3. Battery is empty or virtual connection, please check the

battery voltage and examine whether the wire connection

is firm or not.

Содержание MK4+




















Результаты поиска

Содержание MK4+

Отзывы:

Бренды по названию

Популярные бренды

MarineKinetix MK4+, Руководство пользователя

Результаты поиска

Содержание MK4+

Отзывы:

Бренды по названию

Популярные бренды