Marine Power Solutions MP-4110T Скачать руководство пользователя | Manualshive

Страница: 15 / 23

background image

15

5.4.5 Check the valve clearance

Checking and adjusting the valve clearance should only be done by professional. See

“Valve” under

“Technical Data”.

5.4.6 Check starter and alternator

Checking and maintenance work on the starter and alternator should only be done by professional.

5.4.7 Check cooling system

If the cooling system is functioning normally, the

“TEMP” lamp will not be lit up. If the temperature is

too high and the lamp lights up, the cause maybe one of the following:
Blocked water intake
Defective impeller in sea water pump
Defective thermostat or temperature gauge
Warning: Watch out for water leakage whenever you are working on the cooling system

«
...
13
14
15
16
17
...
»

Содержание MP-4110T
























Отзывы:

Нет отзывов

Похожие инструкции для MP-4110T

Бренд: Danfoss Страницы: 28

Бренд: Parker Страницы: 36

Бренд: Indmar Страницы: 94

Бренд: ZF Страницы: 80

Бренд: ULPOWER Страницы: 25

Johnson BJ25E4SUC

Бренд: BRP Страницы: 265

Бренд: B&S Страницы: 26

Бренд: Nissei Страницы: 16

Бренд: O.S. engine Страницы: 29

Бренд: Toyama Страницы: 48

Бренд: TOHATSU Страницы: 292

Бренд: YS Performance Страницы: 2

Бренд: WEN POWER Страницы: 28

Бренд: LinMot Страницы: 48

Бренд: Robin America Страницы: 83

Бренд: Rotax Страницы: 102

Бренд: Rotax Страницы: 184

Бренд: Raider Страницы: 193

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды