3
12. Disconnect tools.
When not in use, before servicing and when changing
accessories such as blades, bits and cutters.
13. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and adjusting
wrenches are removed from the tool before turning it on.
14. Avoid unintentional starting.
Do not carry a plugged in tool with a finger on the switch
trigger. Ensure switch is off when plugging in.
15. Use outdoor extension leads.
When tool is used outdoors, use only extension cords
intended for outdoor use.
16. Important extension cord information:
a. Make sure the extension cords are in good condition
before use.
b. Based on the total length of cord that you are going
to use, check the chart to make sure the cord meets the
correct minimum cord gauge (AWG) requirements.
IMPORTANT NOTE:
Using an undersized cord or a larger number cord gauge
(AWG) than recommended in the chart, will cause a loss in
power and overheating of the unit. Using a smaller number
cord gauge (AWG) than recommended in the chart, is
acceptable.
Extension cord chart
(
minimum cord gauge (AWG)
)
17. Stay alert.
Watch what you are doing. Use common sense. Do not
operate tool when you are tired, ill or under the influence
of alcohol or other drugs.
18. Check damaged parts.
Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it
will operate properly and perform its intended function.
Check for alignment of moving parts, free running of
moving parts, breakage of parts, mounting and any other
conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired or
replaced by an authorised service centre unless otherwise
indicated in this instruction manual. Have defective
switches replaced by an authorised service facility. Do not
use the tool if the switch does not turn it on and off.
Don’t
operate the machine with a damaged or excessively
worn cutting device.
19. The use of any accessory or attachment, other than those
recommended in this instruction manual, may present a
risk of personal injury.
20. Have your tool repaired by a qualified person.
This electric tool conforms to relevant safety requirements.
Repairs should only be carried out by qualified persons
using original spare parts, otherwise this may result in
considerable danger to the user.
21. Keep in mind that the operator or user is responsible for
accidents or hazards occurring to other people or their
property.
22. Work only in daylight or in good artificial light.
23. Keep all guards attached at all times when unit is operated.
24. Always use the shoulder strap.
Adjust the strap for comfort before starting the motor.
25. Secure unit during transport to prevent damage or injury.
26.
Machine should not be used in any position that causes
any part to come within 3 metres of overhead electrical
lines.
Always be aware of overhead power lines.
27.
Always
keep a firm grip on both handles when motor is
running: one hand grasps the front “loop” handle while the
other hand grasps the rear handle. Severe injuries can
result if you try to use this machine with only one hand or
with an insecure grip.
28.
Thoroughly
inspect the area where equipment is to be
used and removed all objects, which can be thrown by the
machine.
29.
Always
keep area clear of children, pets, and bystanders.
30.
Always
inspect your unit before each use and ensure that
all handles, guards and fasteners are secure, operating, and
in place. Be sure that all electrical cords are not damaged
or broken.
31.
Always
maintain and examine your attachments with care.
Follow maintenance instructions given in manual.
32.
Don’t
attempt to repair any part of the extended reach
E system. Have repairs made by a qualified repairman. See
that only original “Mantis” parts are used.
33. Maintain a firm footing and good balance, do not
overreach while trimming. Before you start to trim, check
the work area for obstacles that might cause you to lose
WARNING – DANGER
LITTLE WONDER WILL NOT BE RESPONSIBLE
FOR THE FAILURE OF CUTTING DEVICES OR
ACCESSORIES THAT HAVE NOT BEEN TESTED
AND APPROVED FOR USE WITH THIS UNIT.
USE ONLY MANUFACTURER-RECOMMENDED
REPLACEMENT PARTS.
Length (metres)
.3 to 7.8 7.9 to 15.5 15.6 to 30.6 30.7 to 45.7
Cord gauge (AWG)
18
16
14
12
