background image

2

1. Important Safety Instructions

1.

Water and Moisture

 – Do not use The 

 near any source of water or in excessively moist 

environments. 

2.

Object and Liquid Entry

 – Care should be taken so that objects do not fall, and liquids are not 

spilled, into the enclosure through the openings. 

3.

Heat & Ventilation

 – When installing The 

 in a rack or any other location, be sure there 

is adequate ventilation. Improper ventilation will cause overheating, and can damage the unit. 
The unit should be situated away from heat sources, or other equipment that produce heat.  

4.

Power Sources

 – The 

 has an internal universal power supply which can operate in any 

country. It has an input voltage range of 90-260 VAC at 50/60 Hz.

5.

Cleaning

 - The 

 can be cleaned with just a damp cloth, or alcohol/methylated spirits for 

more stubborn marks.

6.

Damage

 - If after unpacking your 

 there are signs of shipping damage, contact your 

dealer. 

7.

Servicing

 - Do not attempt any servicing without consulting your dealer or Manley 

Laboratories, Inc. The user should not attempt to service the unit beyond that described in the 
operating instructions. All other servicing should be referred to qualified service personnel. 
This unit has 

high voltages

 present, even after the power has been switched off.

8.   

DO NOT

 connect the AC supply cord until all other connections have been made. Afer initial 

power up the power LED will “blink” for thirty seconds. The unit remains in MUTE until this 
warm up period has elapsed. 

ELOP+

ELOP+

ELOP+

ELOP+

ELOP+

2. Getting Started

Unpacking your MANLEY 

The ELOP+ is secured in its packing carton by two Duracell foam end-caps.

Hold the unit by the middle and simply lift the unit vertically straight out of the box.

After it has been unpacked, check that nothing is loose inside when handling the unit. The unit is 
shipped with the vacuum tubes installed. Make sure they are not loose by looking through the vent 
holes on the top cover. Ensure they are standing upright in their sockets.

It is advisable to keep the original packaging. In the event of servicing or relocating, the original 
packaging ensures that the unit will always be shipped safely.

This package contains the following;

1 x Manley ELOP+ Stereo Limiter Compressor
1 x Manley ELOP+ Owner’s Manual
1 x IEC Power Cable
1 x Warranty Registration Card
1 x Warranty Statement

ELOP+:

Содержание ELOP+

















Отзывы: