background image

MAINS CONNECTIONS

 

Your BACKBONE has been factory set to the correct mains voltage for your country. The voltage setting is 

marked on the serial badge, located on the rear panel. Check that this complies with your local supply.

 

 

Export units for certain markets have a moulded mains plug fitted to comply with local requirements. If your unit 

does not have a plug fitted the coloured wires should be connected to the appropriate plug terminals in accordance 

with the following code:

GREEN/YELLOW  

EARTH

BLUE 

  NEUTRAL

BROWN 

  LIVE

 

As the colours of the wires in the mains lead may not correspond with the coloured marking identifying the termi-

nals in your plug proceed as follows:

The wire which is coloured GREEN/YELLOW must be connected to the terminal in the plug which is 

marked by the letter E or by the safety earth symbol or coloured GREEN or GREEN and YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked by the letter 

N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked by the 

letter L or coloured RED.

DO NOT CONNECT/SWITCH ON THE MAINS SUPPLY UNTIL ALL OTHER CONNECTIONS HAVE 

BEEN MADE.

Note: This unit has been factory wired for your country. If you plan to take the unit to countries with a differ-

ent mains voltage you will need to send the BACKBONE to a qualified service technician or to the Manley Labs 

Service Center for the correct transformer primaries wiring conversion. Alternatively, you may use outboard 

AC voltage step-up or step-down transformers as appropriate.

TRANSFORMER WIRED IN PARALLEL for 100V and 120V operation. Uses a 1A SLO-BLO fuse.

TRANSFORMER WIRED IN SERIES for 220-240V operation. Uses a 0.5A SLO-BLO fuse.

***Fuses for ALL VOLTAGES are 5x20mm GDC packaged fuses.***

Waste Electrical and Electronic Equipment (WEEE)

Information for customers:

The European Parliament and the Council of the European Union have issued the Waste Electrical and Electronic Equipment Directive. The purpose of the Direc-

tive is the prevention of waste of electrical and electronic equipment, and to promote the reuse and recycling and other forms of recovery of such waste. As such 

the Directive concerns producers, distributors and consumers.

The WEEE directive requires that both manufacturers and end-consumers dispose of electrical and electronic equipment and parts in an environmentally safe man-

ner, and that equipment and waste are reused or recovered for their materials or energy. Electrical and electronic equipment and parts must not be disposed of with 

normal household wastage; all electrical and electronic equipment and parts must be collected and disposed of separately.

Products and equipment which must be collected for reuse, recycling and other forms of recovery are marked with the following pictogram:

Small products may not always be marked with this pictogram in which case this is present in the instructions for use, on the guarantee certificate and printed on 

the packaging.

 

When disposing of electrical and electronic equipment by use of the collection systems available in your country, you protect the environment, human health and 

contribute to the prudent and rational use of natural resources. Collecting electrical and electronic equipment and waste prevents the potential contamination of 

nature with the hazardous substances which may be present in electrical and electronic products and equipment.

Your MANLEY or LANGEVIN retailer will assist with and advise you of the correct way of disposal in your country.

4

Содержание Backbone



























Отзывы: