Manitowoc S1000M Скачать руководство пользователя

Страница: 36 / 38

Before Calling For Service

Section 5

5-2

Part Number 80-1561-3

Safety Limit Feature

In addition to the standard safety controls, such as the
high pressure cutout, your Manitowoc ice machine
features built-in safety limits which will stop the ice
machine if conditions arise which could cause a major
component failure.

Before calling for service, re-start the ice machine using
the following procedure:

1. Move the ICE/OFF/CLEAN switch to OFF and then

back to ICE.

A. If the safety limit feature has stopped the ice

machine, it will restart after a short delay.
Proceed to step 2.

B. If the ice machine does not restart, see “Ice

machine does not operate” on the previous
page.

2. Allow the ice machine to run to determine if the

condition is recurring.

A. If the ice machine stops again, the condition has

recurred. Call for service.

B. If the ice machine continues to run, the condition

has corrected itself. Allow the ice machine to
continue running.

Problem

Possible Cause

To Correct

Ice machine produces shallow or
incomplete cubes, or the ice fill pattern on
the evaporator is incomplete.

Ice thickness probe is out of adjustment.

Adjust the ice thickness probe.
(See Section 4)

Water trough level is too low.

Check the water level probe for damage.
(See Section 3)

Water inlet valve filter screen is dirty.

Remove the water inlet valve and clean
the filter screen. (See Section 4)

Water filtration is poor.

Replace the filter.

Hot incoming water.

Connect the ice machine to a cold water
supply. (See Section 2)

Water inlet valve is not working.

Replace the water inlet valve.

Incorrect incoming water pressure.

Water pressure must be 20-80 psi
(138 - 551 kPA)

Ice machine is not level.

Level the ice machine.
(See Section 2)

Low ice capacity.

Water inlet valve filter screen is dirty.

Remove the water inlet valve and clean
the filter screen. (See Section 4)

Incoming water supply is shut off.

Open the water service valve.

Water inlet valve stuck open or leaking.

Place toggle switch in OFF position, if
water continues to enter water trough
replace the water inlet valve.

The harvest assist air compressor is not
functioning.

Call for service.

Содержание S1000M







































Результаты поиска

Содержание S1000M

Отзывы:

Похожие инструкции для S1000M

Бренды по названию

Популярные бренды

Manitowoc S1000M, Инструкция по установке, использованию и уходу

Результаты поиска

Содержание S1000M

Отзывы:

Похожие инструкции для S1000M

Бренды по названию

Популярные бренды