Manitowoc 16000WA, Руководство оператора

Страница: 72 / 110

Reference
Only
SET-UP AND INSTALLATION 16000 WIND ATTACHMENT OPERATOR’S MANUAL
4-42
Published 03-18-13, Control # 116-09
3. Pin handling pendants (6) to assist crane block (7) with
nylon lifting slings (8).
4. Support the mast with the assist crane.
5. Lower the mast to the desired position with the assist
crane.
Do not side load mast.
Use the limit bypass switch to bypass the mast limit and
pay out boom hoist wire rope as the mast is lowered with
the assist crane.
6. Reeve the wire rope from the whip drum through the
sheaves in the mast point and the sheaves in the
assembly block (see Figure 4-4, View A).
7. Anchor the wire rope to the socket and wedge on the
load block (see Wire Rope Installation and Maintenance
in this section).
8. Connect 4-leg chain sling (4) to the assembly block.
9. Raise the mast to at least 156° with the assist crane. As
the mast is raised:
• Pay out load line from whip drum.
• Haul in wire rope on boom hoist.
10. Once the mast is at or above 156°, support the mast with
the boom hoist wire rope and disconnect handling
pendants (6) from the assist crane block.
11. Pin the handling pendants to the mast for storage (View
A).
12. Haul in load line on the whip hoist to lift the assembly
block off the trailer.
Take every precaution to prevent
block from swinging into end of boom butt and
causing damage.
13. Position the mast in the operating range (see Section 4
of Crane Operator’s Manual).
Remove Boom Butt
See Figure 4-18 for following procedure.
1. Lower the wire rope guide to the shipping position:
a. Attach a lifting sling from the assembly block to
lifting lug (3, View A) on wire rope guide (2).
b. Support the wire rope guide so pins (4) are loose
and remove the pins.
c. Lower the wire rope guide from the operating
position to the shipping position.
d. Install pins (4).
e. Disconnect the lifting sling.
2. Disconnect the hydraulic hoses between the boom butt
and the rotating bed (see Figure 4-19):
a. Thoroughly clean each coupler and connect
s e a l i n g c o v e r s t o c o u p l e r s t o p r e v e n t d i r t
accumulation.
b. Unpin and move retaining bar (2) out of way.
c. Swing hydraulic hoses (6 and 7) rearward into the
notches on the rotating bed (View D).
d. Pin the retaining bar in position to retain the hoses
(View D).
3. Attach lifting slings from the assembly block to the lifting
lugs on the boom butt as shown in Figure 4-18, View D.
4. Disconnect hydraulic hoses (5a, View B) from couplers
(5b) in the boom butt.
Thoroughly clean couplers to prevent dirt from
entering hydraulic system.
5. Connect hydraulic hoses (5a, View C) to couplers (5c)
on the left side of the rotating bed.
6. Remove locking pins (7, View E) from the operating
position and install them in the shipping position.
7. Attach hand-held taglines to the butt so it can be
stabilized when the pins are disconnected.
8. Lift the butt clear of the ground (View D).
9. Using the setup remote control, disengage boom hinge
pins (6, View E).
10. Stabilize the butt with the taglines.
11. Raise the butt just clear of the rotating bed and engage
boom hinge pins using the setup remote control,
WARNING
Crush Hazard!
Do not stand or work under mast unless it is supported by
assist crane.
CAUTION
Equipment Damage!
To prevent damage, guide mast straps (9) clear of trailer,
as required.
WARNING
Moving Load Hazard!
Warn personnel to stand well clear of boom butt. Butt may
swing out away from crane when pins are disengaged.