M&G Duravent Duratech Canada HT Скачать руководство пользователя страница 4

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

4

GENERAL INSTALLATION NOTES

INSTALLATION NOTES

1

1.   The chimney is intended for use with solid (6’’,7’’,8’’ dia. only) or   

liquid and gaseous fuel burning appliances.(all diameters)

   Allowable flue gas temperature:

      

Maximum continuous 540°C (1000°F)

      

Brief forced firing 760°C (1400°F) 

 

 

 

   

Tested to 1150°C (2100°F) - 30 minutes

2.   

On wood or coal stove application and in area where the chimney 

is completely enclosed, it is required to install Premium shields 

(telescopic of flexible)  around the chimney and a Radiation shield 

connector at the ceiling level.

 

   For venting of gas or oil burning appliances Premium shields are 

not required even where the chimney is enclosed.  

   For factory-built wood burning fireplaces, Premium shields are 

usually not required, please follow fireplace installation instruction.

3.   The maximum height of chimney supported by the various supports 

are outlined on page 3.

4.   The  supports  described  in  this  booklet  should only  be used with 

Duravent model DURATECH CANADA (DTC), 5", 6", 7", 8" and 10" 

factory built chimneys.

5.   Size the chimney in accordance with the appliance manufacturer's 

instructions.

6.   When a firestop (DTC-FS , DTC-ISI or DTC-RSCI) needs to be installed, 

it is important to follow the opening dimensions for the floor open-

ings prescribed in this manual. This way, the holes left by the folded 

positioning tab of the firestop will be blocked by the ceiling.

7.   A chimney servicing a fireplace or an incinerator shall not serve any 

other appliance.

8.   The chimney shall extend at least 3 ft above its point of contact with 

the roof and at least 2 ft higher than any wall, roof or adjacent building 

within 10 ft of it.

9.   The maximum height of unguided chimney above the roof is 5 ft.

10.  The clearance between single wall pipe and unprotected combustible 

material must not be less than 18" (see national building code and 

NFPA 211) except: The distance between the vertical stove pipe and 

the ceiling may be less than 18" and will be established by the finish 

support.

11.  Portions of the chimney which may extend through accessible spaces 

shall be enclosed in all cases to avoid personal contact with the chimney 

and damage to the chimney. When doing so on woodstove or coal 

application, a telescopic or flexible Premium shield must be installed 

(

see Figure 2

).  Except for installation in single and two-story family 

dwellings, the enclosure must have a fire resistance rating equal to 

or greater than that of the floor or roof assemblies through which 

they pass.

12.  Do not fill the 2" space around the chimney with insulation or any 

other material.  Insulation placed in this area could cause adjacent 

combustibles to overheat.

13.  Self tapping screws are not required, but may be used to reinforce 

the connection and avoid accidental unlocking of chimney lengths.

2 ft

MIN.

10 ft

3 ft

 MIN.

2" MIN.

ENCLOSURE

2" MIN.

7 1/2"

MIN.

BASE TEE

* 18"

MINIMUM

* 18"

MINIMUM

*  THE DISTANCE CAN BE REDUCED IF A 

LISTED STOVE PIPE IS USED.

Figure 2

       WARNING 

The clearance between the chimney and combustible

material must not be less than 2", except where

established by the support. Do not fill this area with

insulation.

RADIATION

SHIELD 

CONNECTOR 

(DTC-RSCI)

STORM

COLLAR

(DTC-SC)

RADIATION

SHIELD 

FIRESTOP 

(DTC-FRSC)

SWIVEL 

ADAPTOR 

OPTIONAL

(DTC-SA)

PREMIUM SHIELD 

(DTC-TRS or DTC-FLXS)

SUPPORT

(DTC-FSC 

OR DTC-BS)

Содержание Duravent Duratech Canada HT

















Отзывы: