Mammoth 211400 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 20

background image

Mammoth Fans INDUSTRIAL SERIES |

11

FAN INSTALLATION

9. STEEL WIRING

Important – support wires should be evenly spaced in 4 opposing directions to evenly
distribute any stress and movement. Wire clamps should be secure and glued with screw
glue (Loctite or similar)

10. POWER CABLE

Wiring should be to local regulations

11. FAN BLADES

Fan blades should be mounted one after the other in opposites to each other, two people
will be required to effectively mount and tighten the fan blades and safety support screws.
This procedure must be done while the fan motor is mounted on the ceiling. Trying to
compete this on the floor then mounting the fan will cause damage to the blades.

12. FAN BLADE TIP

INSTALLATION

Fan Blade Tip

13. CONTROL
SYSTEM

The height from floor to the bottom of the control box should be around
1.2 meters and in a safe and practical position

14. WIRING

Distinguish the input and output, also make sure the ground wire is in place,
wire to local wiring standards.

«
...
9
10
11
12
13
...
»

Содержание 211400





















Отзывы:

Нет отзывов

Похожие инструкции для 211400

100MM/4" RANGE DX100

Бренд: Xpelair Страницы: 10

Бренд: Easy@Home Страницы: 26

SERENITY VU3520S1

Бренд: TEFAL Страницы: 20

Бренд: Litex Industries Страницы: 10

ALPATEC NEW BABEL DIGITAL

Бренд: Taurus Страницы: 36

Бренд: Domo Страницы: 36

Бренд: Fanco Страницы: 16

BLUSH LP7678LMW

Бренд: Fanimation Страницы: 40

Cancun FP8009OB-220

Бренд: Fanimation Страницы: 16

Бренд: Hunter Страницы: 13

Бренд: HAMPTON BAY Страницы: 16

Бренд: Maico Страницы: 3

Бренд: ebm-papst Страницы: 13

Бренд: Chiller Страницы: 45

Бренд: Fanimation Страницы: 10

Бренд: Vaxcel Страницы: 8

Бренд: B-Air Страницы: 24

Бренд: S&P Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды