INTRODUCTION:-
Thank you for purchasing a Malta Dynamics 4-Person Rope HLL. This manual must be read and understood in its entirety, and
used as part of an employee training program as required by OSHA or any applicable state agency.
This and any other included instructions must be made available to the user of the equipment. The user must understand how to
safely and effectively use the 4-Person Rope HLL, and all fall safety equipment used in combination with the 4-Person Rope HLL.
Applicable Safety Standards
When used according to instruction specifications, this product meets or exceeds
EN 795:2012 Type C & TS 16415 TYPE C
standards
for fall protection. Applicable standards and regulations depend on the type of work being done, and also might include state-specific
regulations. Consult regulatory agencies for more information on personal fall arrest systems and associated components.
Worker Classifications
Qualified Person:
A person with an accredited degree or certification, and with extensive experience or sufficient professional standing, who is
considered proficient in planning and reviewing the conformity of fall protection and rescue systems
Competent Person:
A highly trained and experienced person who is ASSIGNED BY THE EMPLOYER to be responsible for all elements of a fall
safety program, including, but not limited to, its regulation, management, and application. A person who is proficient in identifying
existing and predictable fall hazards, and who has the authority to stop work in order to eliminate hazards.
Authorized Person:
A person who is assigned by their employer to work around or be subject to potential or existing fall hazards. It is the
responsibility of a Qualified or Competent person to supervise the job site and ensure all applicable safety regulations are complied with.
IMPORTANT BEFORE INSTALLATION AND USE :-
Prior to use, plan your system:
1. Ensure all PFAS equipment is selected and deemed compatible by a Competent Person.
2. Eliminate or minimize all risk of swing fall.
3. Determine desired location for HLL; ensure location is free of debris, rot,
decay, cracking, and hazardous materials.
4. Installation, set-up, and use of HLL system must be done under the
supervision of a Qualified Person.
Recommended Maximum Users: 4
Installation Of Temporary Horizontal Lifeline
HLL3001 :
Step 1: The receiving structure onto which lifeline is to be installed must be
strong enough to hold an impact load of more than 5,000 lbs.Fig. 01
Step 2: Installation of rope into the tensioner:
a) Loosen the knob to slide open the housing cover plate.
Fig. 02
b) Pull back the Hockey and Lock Body so as to create adequate gap to
insert rope around the pulley. Please refer attached image for the
direction of rope insertion. Fig. 03
c) Slide back the cover plate and ensure that hole on cover plates match
with spacer on the fixed cover plate. Fig. 04
d) Once aligned, re-tighten the knob to the fullest to hold the cover
plates in position. Fig. 05
Step 3 : With help of a carabiner attached to the swivel connector of lifeline
connect the rope to a suitable anchorage point. (In case of any
unavailability of anchor point use Malta Dynamics Cross Arm Strap
to create one.) Fig. 01
Step 4: Now connect the tensioner to the second anchorage point along with
tension indicator by attaching a carabiner to the hokey eye of tension
indicator. Fig. 06
Step 5 : Pull the initial slack of rope by hand and ensure that rope is seated
properly in the groove of pulley. Fig. 07
Step 6 : Use an open end spanner of 0.944 inches provided along with
tensioner to give appropriate tension to the lifeline. Plate of Tension
indicator will start to rotate freely once the required tension has been
achieved in lifeline. Now, O rings/ pass through carriages can be
used as mobile anchors for the workers. Fig. 08
Step 7 : To uninstall the lifeline, push the lock backwards in order to pull back
the hockey. Hockey will release the pulley and allow rope to loosen.
Fig. 9
OSHA,
HLL3001
Applicable to
:
HLL3001
Manufacturer
:
MALTA DYNAMICS LLC
210 13th Street | Malta, OH 43758
Certification Body
:
SATRA Technology Centre Kettering, Northants, UK
(Notified Body 0321)
Ongoing Assessment Body
:
SGS United Kingdom Ltd., Unit 202B, Worle Parkway,
Weston-super-Mare, BS22 6WA, UNITED KINGDOM.
(Notified Body 0120)
USER INSTRUCTIONS
Do not skip this instruction manual. Read the instruction manual carefully before using the equipment. If failed in doing so it may
cause serious Injury or Death.
Fig 04
Fig 02
Knob
Housing
Cover
Plate
Fig 06
Tension
Indicator
Fig 08
Spanner
Indicator
Plate
Fig 01
Cross
Arm Strap
Structure
Fig 03
Hockey
Lock
Fig 05
Pull the Rope
for proper tension
Fig 07
Pulley
Page 1 of 4
