Malibu Boats 2008 iRide Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 112

Malibu Boats 2008 iRide Скачать руководство пользователя страница 61

2-31

Due to the many stereo accessories, and additional boat
optional stereo components that can be added to this
system, it is very easy to overload the boat’s electrical
systems capability to recharge your battery resulting in a
dead battery.

If you will be adding additional equipment to your boat, it is
recommended that you have a trained technician calculate
draw and amperage of the electrical system before adding
equipment. Higher Amp alternators are available to prevent
an overloaded system.

Hot Water Shower

If your boat is equipped with a hot water shower, you will find an ON/OFF accessory
switch located on the dash panel. You will find the valves located on the port side of the
motorbox compartment. The shower head can be found in the port gunnel sides. You
should find specific instructions on the use of your hot water shower in the packet of
materials you received with your boat.

Figure 2-36. Shower Head

Figure 2-37. Shower Valve

Pull-Up Cleats

Pull-Up cleats are available for all boat models. These
cleats will sit flush on the side of the boat deck when
depressed. To pull up the cleats, simply press the
screw/button located in the center of the cleat. To depress
the cleat, simply press the cleat downward until it locks
into place.

Docking Lights

The docking lights should only be used during slow speed docking maneuvers. The lights
are activated by a switch on the accessory switch panel and have a 10 amp circuit
breaker. Bulb access is through the lens cover outside the boat. Replacement bulbs:

•

Standard Lights: 12V 30W EXT

•

25' Lights: H7614 Sealed Beam

Figure 2-38. Pull-Up Cleat

Chapter 2_08.qxd: Chapter 2 doc.qxd 11/12/07 3:32 PM Page 31

«
...
59
60
61
62
63
...
»

Содержание 2008 iRide

















































































































Отзывы:

Нет отзывов