manualshive.com logo in svg

MAKSIWA BMS.3200.IR, Инструкция по эксплуатации

Поделиться
Скачать
MAKSIWA BMS.3200.IR Скачать руководство пользователя страница 52

52

6 Troubleshooting Guide 

•  The necessary interventions should be made by our technical specialists. For any maintenance 

or repairs, please turn off the machine, remove the machine from the power supply and wait until 

the blade stop completely and then proceed with the service. 

•  For any problem, information or abnormality with the machine, contact the distributor in your 

area or directly with our service center after sale of MAKSIWA INTERNATIONAL INC., through 
844-319-6594

6 Troubleshooting Guide

Problem

Possible Cause

Solution

Saw stopped, no longer spins.

Excessive load on the motor.

Wait for motor to cool off, then flip off/on 

circuit breaker.

Saw has fallen off of shaft.

Check washer and lock nut.

Triggered circuit breaker.

Flip circuit breaker off/on.

Damaged or loose wire.

Locate and replace wire.

Does not make exact cuts at 45° or 90°.

Misaligned blade stopper.

Adjust the stop.

Wood is warped.

Replace wood for a good piece.

Loose blade nut/ Warped saw blade.

Tighten nut or replace Blade.

Riving knife not aligned.

Riving knife with the saw blade.

Saw makes unsatisfactory cuts.

Worn Blade.

Sharpen or replace blade.

Mounted in the wrong direction.

Flip the blade.

Glue on the blade.

Remove and clean blade.

Worn blade for the material being cut.

Use correct blade.

Glue on the table.

Clean the table.

Blade does not keep constant speed.

Incorrect wire gauge/size.

Use correct gauge/size wire.

Low voltage.

Call electric service provider.

Motor wiring is setup is incorrect.

Check and adjust wiring in motor.

Saw blade vibrates

Machine is not level.

Put the machine at level.

Blade is damage.

Replace blades.

Damage belt.

Replace belt.

Pulled is tilted.

Replace pulley.

Montagem imprópria do motor.

Verifique e ajuste o motor.

Motor was assembled in the wrong 

position

Verify and adjust the motor.

Hight guide is loose.

Tighten or adjust guide.

Wood kicks back when it comes in contact 

with the blade.

Aluminum guide is misaligned.

Align the guide.

Riving knife misaligned.

Align the riving knife.

Cut was made without guide support.

Install and use the guide.

Worn blade.

Replace the blade.

Piece was not held correctly.

Hold piece all the way through.

Blade has no height adjustment and slope.

The elevation system is too tight.

Adjust the elevation system.

Dust and chips of wood are in the elevation 

system.

Clean and lube the components.

Содержание BMS.3200.IR























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды