Maksan MKF-20G, Инструкция по установке, эксплуатации и обслуживанию

Страница: 32 / 33

32
3.1 “DRY HEATING” CYCLE
● To program adry cooking cycle (without moisture) simply
turn the selector knob
“B” to position “5” and set the
required cooking temperature and time”
3.3 RAPID OVEN COOLING
To rapidly cool down the oven after a cooking cycle, proceed
as follows:
● Open the oven door, and the selector knob
"B" to position
“4”.
The fan motor operating time is cotrolled by the operator.
4. TURNING OFF THE OVEN IN THE
EVENT OF FAULTS
In the event of faults, switch off the appliance as follows:
● Disconnect the appliance from the main power supply at
the isolating switch and close the water and gas cocks.
● Contact a technical service centre with personel trained
and authorised by the manufacturer.
5. CARE AND MAINTENANCE
● Disconnect the appliance from the main power supply at
the isolating switch and close the water and gas cocks.
● At the end of each day clean the oven interior with an
oven cleaner, following the directions given by the product
supplier.
● Do not wash the appliance with jets of water.
● Do not use products containing chlorine (bleach,
hydrochloric acid etc.) even diluted, to clean the steel
surfaces.
● Do not use corrosive substances (i.e. muriatic acid) to
clean the floor underneath the appliance.
MAINTENANCE, INSPECTIONS, CHECKS
AND CLEANING
FREQUENCY
Routine cleaning
Daily
General Cleaning of machine and
surrounding area
Mechanical protection devices
Mounthly
Check condition and for any deformation ,
loosening or removed parts.
Control and Machine structure
Yearly
Check mechanical part for any breakage or
deformation, tightening of screws. Check
readability and condition of words, stickers
and symbols and restore if necessary.
Electrical connection cable and plug
Yearly
Check connection cable (replace it if
necessary) and plug.
To facilitate the task of cleaning the oven, remove the trolley
mounted unit runners in the oven base (if fitted), and also
the lateral air diffusors supporting the oven trays, and the
fan suction panel.
●To remove the
air diffusors inside the oven, proceed as
follows:
- Lift the diffusor and rotate to release the two front pins.
This done, remove the diffusor by detaching the hooks from
the slots in the fan panel.
To remount the diffusor, simply repeat the above procedure
in reverse order.
● To remove
fan suction panel “A” (Fig. “9”) inside the oven,
proceed as follows:
- Remove the lateral air diffusors, ondo the two fixing screws
“D” and , if necessary, lower humidifier “E”, by slackening the
corresponding fixing screws.
- Lift the panel and detach from the two bolts at the bottom
of the oven
Note: The two arrows on the panel indicate the position of
the holes for the bolts at the bottom of the oven.
To remount the fan panel, simply repeat the above
procedure in reverse order.
9
Cleaning the oven chamber drain pipe
Periodically clean the drain pipe from inside the oven.
● Clean the stainless steel surfaces daily using lukewarm
soapy water. Rinse thoroughly and dry carefully.
● Never use abrasive materials such as steel wool pads, iron
brushers or scrapers to clean the stainless steel surfaces, since
they may leave ferrous particles on the steel surface, causing
it to rust.
● If the appliance is to remain idle for long periods, proceed
as follows:
- Disconnect from the electrical power supply at the isolating
switch and close the water and gas cocks;
- Using a cloth soaked in vaseline oil, vigorously rub the
stainless steel surffaces until they are wrll lubricated;
- Periodically air the premises.
Changing the oven light bulb
● Should be done only by qualified service personnel
E
D
A