26 ENGLISH
2.
Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
►
Fig.26:
1.
Nut
2.
Cup
3.
Clamp washer
4.
Cutter
blade
5.
Spindle
6.
Receive washer
7.
Hex
wrench
3.
Mount the cutter blade onto the receive washer
so that the arrows on the cutter blade and protector are
pointing in the same direction.
►
Fig.27:
1.
Arrow
4.
Put the clamp washer and cup onto the cutter
blade and then tighten the nut securely by the box
wrench.
►
Fig.28:
1.
Box wrench
2.
Hex wrench
3.
Loosen
4.
Tighten
NOTE:
Tightening torque : 20 - 30 N•m
5.
Remove the hex wrench from the gear case.
To remove the cutter blade, follow the installation proce-
dures in reverse.
Chisel blade
For UR006G only
Optional accessory
1.
Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
►
Fig.29:
1.
Nut
2.
Cup
3.
Clamp washer
4.
Cutter
blade
5.
Spindle
6.
Receive washer
7.
Hex
wrench
2.
Mount the cutter blade onto the receive washer
so that the arrows on the cutter blade and protector are
pointing in the same direction.
►
Fig.30:
1.
Arrow
3.
Put the clamp washer and cup onto the cutter
blade and then tighten the nut securely by the box
wrench.
►
Fig.31:
1.
Box wrench
2.
Hex wrench
3.
Loosen
4.
Tighten
NOTE:
Tightening torque : 20 - 30 N•m
4.
Remove the hex wrench from the gear case.
NOTICE:
After installing the cutter blade, make
sure that the gap between the cutter blade and
the protector at the position shown in the figure
is within the range of 2.0 to 3.0 mm. If the gap is
not within the range of 2.0 to 3.0 mm, install the
protector again so that the gap is within the range
of 2.0 to 3.0 mm.
►
Fig.32:
(1)
2.0 - 3.0 mm
(2)
Protector
(3)
Cutter
blade
To remove the cutter blade, follow the installation proce-
dures in reverse.
Nylon cutting head
NOTICE:
Be sure to use genuine Makita nylon
cutting head.
►
Fig.33:
1.
Nylon cutting head
2.
Spindle
3.
Hex
wrench
4.
Loosen
5.
Tighten
1.
Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
2.
Place the nylon cutting head onto the spindle and
tighten it securely by hand.
3.
Remove the hex wrench from the gear case.
To remove the nylon cutting head, follow the installation
procedures in reverse.
Plastic blade
NOTICE:
Be sure to use genuine Makita plastic
blade.
►
Fig.34:
1.
Plastic blade
2.
Spindle
3.
Hex wrench
4.
Loosen
5.
Tighten
1.
Insert the hex wrench through the hole in the gear case to lock
the spindle. Rotate the spindle until the hex wrench is fully inserted.
2.
Place the plastic blade onto the spindle and
tighten it securely by hand.
3.
Remove the hex wrench from the gear case.
To remove the plastic blade, follow the installation pro-
cedures in reverse.
OPERATION
Attaching the shoulder harness
WARNING:
Be extremely careful to maintain
control of the tool at all times. Do not allow the tool
to be deflected toward you or anyone in the work
vicinity.
Failure to keep control of the tool could result
in serious injury to the bystander and the operator.
CAUTION:
Always use the shoulder harness
attached to the tool. Before operation, adjust the
shoulder harness according to the user size to
prevent fatigue.
CAUTION:
Before operation, make sure that
the shoulder harness is properly attached to the
hanger on the tool.
CAUTION:
When you use the tool in combi-
nation of the backpack-type power supply such
as portable power pack, do not use the shoulder
harness included in the tool package, but use the
hanging band recommended by Makita.
If you put on the shoulder harness included in the
tool package and the shoulder harness of the back-
pack-type power supply at the same time, removing
the tool or backpack-type power supply is difficult in
case of an emergency, and it may cause an accident
or injury. For the recommended hanging band, ask
Makita Authorized Service Centers.
Содержание UR007GM101
