background image

18

Guarantee

MAKITA guarantees the highest quality and will therefore reimburse all costs for mending through replacement of damaged parts as
a result of material or production faults, which occur within the guarantee time after purchase.
Please, note that in some countries particular guarantee conditions may exist. In case of any doubts, please, contact your salesman
who is responsible for the guarantee of the product.
We ask for your understanding that we cannot accept any responsibility for damage caused by:

Disregard of the instruction manual.

Non-performance of the required maintenance and cleaning instructions.

Normal wear and tear.

Obvious overload due to permanent excess of the upper limits of capacity.

Use of guide bars and saw chains which have not been approved.

Use of guide bar and saw chain lengths which have not been approved.

Use of force, improper use, misuse or accidents.

Damage caused by overheating due to dirt obstructing the cool air supply at the motor case.

Use of unsuitable spare parts or parts which are not original MAKITA parts, as far as they have caused the damage.

Use of unsuitable or old oil.

Damage related to conditions arising from lease or rent contracts.

Works on the chain saw by unskilled persons or performance of inappropriate repairs.

Cleaning, servicing and adjustment works are not covered by the guarantee. All repairs covered by the guarantee are to be performed
by a MAKITA service centre.

Extract from the spare parts list

Use original MAKITA spare parts only. For performance of repairs and for replacement of other
components your MAKITA service centre should be consulted.

 Included in the delivery inventory

2

3

4

5

1

  Pos.  MAKITA No.    Qty.

Denomination

   1

953 100 090 1

Chain gauge 3/8”

   2

953 004 010 1

File handle

   3

953 003 090 1

Round file  ø 4 mm

   4

953 003 060 1

Flat file

   5

953 030 010 1

File holder compl. 3/8”

  Pos.  MAKITA No.       Qty. Denominatio

   1

205 114 201 1

Oil tank cap compl.

1

1

1

   2

901 505 354 1

Screw for chain tightener

1

1

1

   3

001 213 042 1

Nut with pin

1

1

1

   4

923 208 004 1

Fastening nut

1

1

1

   5

225 213 100 1

Sprocket guard

1

1

1

   6

957 802 410 2

Carbon brushes

1

1

1

   7

442 030 661 1

Sprocket nose bar 30 cm (12")

1

   7

442 035 661 1

Sprocket nose bar 35 cm (14")

1

   7

442 040 661 1

Sprocket nose bar 40 cm (16")

1

   8

528 092 646 1

Saw chain 3/8" für 30 cm

1

   8

528 092 652 1

Saw chain 3/8" für 35 cm

1

   8

528 092 656 1

Saw chain 3/8" für 40 cm

1

   9

952 100 633 1

Chain protection cover (30-40 cm)

1

1

1

   10 941 713 001 1

Universal wrench SW 13

1

1

1

3001A   3501A   4001A

Accessories
(not included in the delivery inventory)

1

2

9

4

10

5

8

3

6

7

Содержание UC 3001A





















Отзывы: