background image

7 ENGLISH

Adjusting depth of cut

CAUTION:

 

After adjusting the depth of cut, 

always tighten the clamping screw securely.

1

2

►    

1.

 Clamping screw 

2.

 Depth guide

Loosen the clamping screw on the depth guide and 

move the base up or down. At the desired depth of cut, 

secure the base by tightening the clamping screw.

Bevel cutting

1

2

►    

1.

 Clamping screw 

2.

 Bevel scale plate

Loosen the clamping screw on the bevel scale plate on 

the front of the base. Set for the desired angle (0° - 45°) 

by tilting accordingly, then tighten the clamping screw 

securely.

Sighting

1

B

A

►    

1.

 Cutting line

For straight cuts, align the A position on the front of the 

base with your cutting line. For 45° bevel cuts, align the 

B position with it.

Switch action

CAUTION:

 

Before installing the battery car-

tridge into the tool, always check to see that the 

switch trigger actuates properly and returns to 

the "OFF" position when released.

CAUTION:

 

Do not pull the switch trigger 

hard without pressing the lock-off lever. This can 

cause switch breakage.

1

2

►    

1.

 Lock-off lever 

2.

 Switch trigger

To prevent the switch trigger from being accidentally 

pulled, a lock-off lever is provided. To start the tool, slide 

the lock-off lever and pull the switch trigger. Release the 

switch trigger to stop.

ASSEMBLY

CAUTION:

 

Always be sure that the tool is 

switched off and the battery cartridge is removed 

before carrying out any work on the tool.

Installing or removing diamond 

wheel

CAUTION:

 

Use only the Makita wrench to 

install or remove the diamond wheel.

CAUTION:

 

When installing the diamond 

wheel, be sure to tighten the bolt securely.

CAUTION:

 

Always install the diamond wheel 

so that the arrow on the diamond wheel points in 

the same direction as the arrow on the diamond 

wheel case.

 Otherwise the wheel rotates in reverse, 

it may cause personal injury.

Содержание TD110DWY













Отзывы: