background image

6

ENGLISH

ASSEMBLY

CAUTION:

 

Always be sure that the tool is 

switched off and unplugged before carrying out 
any work on the tool.

Installing side grip (handle)

Optional accessory for M9506 in some countries

CAUTION:

 

Always be sure that the side grip is 

installed securely before operation.

Screw the side grip securely on the position of the tool 

as shown in the figure.

Installing or removing wheel guard 
(For depressed center wheel)

WARNING:

 

When using a depressed center 

wheel, the wheel guard must be fitted on the tool 

so that the closed side of the guard always points 
toward the operator.

Mount the wheel guard with the protrusions on the 
wheel guard band aligned with the notches on the bear-
ing box. Then rotate the wheel guard to such an angle 
that it can protect the operator according to work. Be 
sure to tighten the screw securely.
To remove wheel guard, follow the installation proce-
dure in reverse.

1

2

►    

1.

 Wheel guard 

2.

 Bearing box 

3.

 Screw

Installing or removing depressed 
center wheel

Optional accessory

WARNING:

 

When using a depressed center 

wheel, the wheel guard must be fitted on the tool 

so that the closed side of the guard always points 
toward the operator.

CAUTION:

 

Make sure that the mounting part 

of the inner flange fits into the inner diameter of 

the depressed center wheel perfectly.

 Mounting 

the inner flange on the wrong side may result in the 

dangerous vibration.

Mount the inner flange onto the spindle. Make sure to fit 

the straight part of the inner flange onto the straight part 

at the bottom of the spindle. Fit the depressed center 

wheel on the inner flange and screw the lock nut onto 

the spindle.
In case of mounting a depressed center wheel thinner 

than 4 mm (5/32″), place the lock nut so that the protru

-

sion on the lock nut faces outside. Otherwise, place it 

so that the protrusion on it fits into the inner diameter of 

the wheel.

1

2

4

3

►    

1.

 Lock nut 

2.

 Depressed center wheel 

3.

 Inner 

flange 

4.

 Mounting part

To tighten the lock nut, press the shaft lock firmly so 

that the spindle cannot revolve, then use the lock nut 
wrench and securely tighten clockwise.

1

2

►    

1.

 Lock nut wrench 

2.

 Shaft lock

To remove the wheel, follow the installation procedure 
in reverse.

Содержание M9507









Отзывы: