![background image](http://html.mh-extra.com/html/makita/ls1440/ls1440_instruction-manual_232366009.webp)
9 ENGLISH
11.
Provide adequate support such as table exten-
sions, saw horses, etc. for a workpiece that is wider
or longer than the table top.
Workpieces longer or
wider than the mitre saw table can tip if not securely
supported. If the cut-off piece or workpiece tips, it can
lift the lower guard or be thrown by the spinning blade.
12.
Do not use another person as a substitute for a
table extension or as additional support.
Unstable
support for the workpiece can cause the blade to bind
or the workpiece to shift during the cutting operation
pulling you and the helper into the spinning blade.
13.
The cut-off piece must not be jammed or pressed
by any means against the spinning saw blade.
If
confined, i.e. using length stops, the cut-off piece could
get wedged against the blade and thrown violently.
14.
Always use a clamp or a fixture designed to
properly support round material such as rods
or tubing.
Rods have a tendency to roll while
being cut, causing the blade to "bite" and pull the
work with your hand into the blade.
15.
Let the blade reach full speed before contact-
ing the workpiece.
This will reduce the risk of the
workpiece being thrown.
16.
If the workpiece or blade becomes jammed,
turn the mitre saw off. Wait for all moving
parts to stop and disconnect the plug from
the power source and/or remove the battery
pack. Then work to free the jammed material.
Continued sawing with a jammed workpiece could
cause loss of control or damage to the mitre saw.
17.
After finishing the cut, release the switch, hold
the saw head down and wait for the blade to stop
before removing the cut-off piece.
Reaching with
your hand near the coasting blade is dangerous.
18.
Hold the handle firmly when making an incom
-
plete cut or when releasing the switch before the
saw head is completely in the down position.
The
braking action of the saw may cause the saw head to
be suddenly pulled downward, causing a risk of injury.
19.
Only use the saw blade with the diameter that
is marked on the tool or specified in the man
-
ual.
Use of an incorrectly sized blade may affect
the proper guarding of the blade or guard opera-
tion which could result in serious personal injury.
20.
Only use the saw blades that are marked with a speed
equal or higher than the speed marked on the tool.
21.
Do not use the saw to cut other than wood,
aluminum or similar materials.
22.
(For European countries only)
Always use the blade which conforms to EN847-1.
Additional instructions
1.
Make workshop kid proof with padlocks.
2.
Never stand on the tool.
Serious injury could
occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
3.
Never leave the tool running unattended. Turn
the power off. Do not leave tool until it comes
to a complete stop.
4.
Do not operate saw without guards in place.
Check blade guard for proper closing before
each use. Do not operate saw if blade guard
does not move freely and close instantly.
Never clamp or tie the blade guard into the
open position.
5.
Keep hands out of path of saw blade. Avoid
contact with any coasting blade. It can still
cause severe injury.
6.
Always secure all moving portions before
carrying the tool.
7.
Stopper pin which locks the cutter head down
is for carrying and storage purposes only and
not for any cutting operations.
8.
Check the blade carefully for cracks or dam-
age before operation. Replace cracked or dam-
aged blade immediately. Gum and wood pitch
hardened on blades slows saw and increases
potential for kickback. Keep blade clean by
first removing it from tool, then cleaning it with
gum and pitch remover, hot water or kerosene.
Never use gasoline to clean blade.
9.
Use only flanges specified for this tool.
10.
Be careful not to damage the arbor, flanges
(especially the installing surface) or bolt.
Damage to these parts could result in blade
breakage.
11.
Make sure that the turn base is properly
secured so it will not move during operation.
Use the holes in the base to fasten the saw to a
stable work platform or bench. NEVER use tool
where operator positioning would be awkward.
12.
Make sure the shaft lock is released before the
switch is turned on.
13.
Be sure that the blade does not contact the
turn base in the lowest position.
14.
Hold the handle firmly. Be aware that the saw
moves up or down slightly during start-up and
stopping.
15.
Make sure the blade is not contacting the
workpiece before the switch is turned on.
16.
Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate poor installation
or a poorly balanced blade.
17.
Stop operation immediately if you notice any-
thing abnormal.
18.
Do not attempt to lock the trigger in the "ON"
position.
19.
Always use accessories recommended in this
manual. Use of improper accessories such as
abrasive wheels may cause an injury.
20.
Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
Additional safety rules for the laser
1.
LASER RADIATION, DO NOT STARE INTO THE
BEAM OR VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS, CLASS 2M LASER PRODUCT.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Содержание LS1440
Страница 3: ...2 1 3 1 2 4 3 1 2 1 1 1 1 1 4 3 2 Fig 8 Fig 9 Fig 10 Fig 11 Fig 12 Fig 13 Fig 14 Fig 15 3 ...
Страница 5: ...1 2 3 4 5 1 2 2 3 4 1 2 1 2 1 2 3 1 Fig 24 Fig 25 Fig 26 Fig 27 Fig 28 Fig 29 Fig 30 Fig 31 5 ...
Страница 6: ...1 1 2 1 2 3 1 2 3 1 1 2 Fig 32 Fig 33 Fig 34 Fig 35 Fig 36 Fig 37 6 ...