![background image](http://html1.mh-extra.com/html/makita/ls1016l/ls1016l_instruction-manual_4273598025.webp)
25
In the case of right bevel cut
Table (A)
006363
Table (B)
006364
Example:
In the case of cutting 52/38° type crown molding for position (1) in
Fig. 54 & 55
:
• Tilt and secure bevel angle setting to 33.9° RIGHT.
• Adjust and secure miter angle setting to 31.6° RIGHT.
• Lay crown molding with its broad back (hidden) surface down on the turn base with its WALL CONTACT EDGE
against the guide fence on the saw.
• The finished piece to be used will always be on the RIGHT side of the blade after the cut has been made.
Crown molding stoppers (optional accessories) allow easier cuts of crown molding without tilting the saw blade. Install
them on the base as shown in the figures.
(Fig. 56 & 57)
Fig. 56: At right 45° miter angle
Fig. 57: At left 45° miter angle
Position crown molding with its WALL CONTACT EDGE against the guide fence and its CEILING CONTACT EDGE
against the crown molding stoppers as shown in the figure
(Fig. 58)
. Adjust the crown molding stoppers according to
the size of the crown molding. Tighten the screws to secure the crown molding stoppers. Refer to the table (C) for the
miter angle.
Table (C)
006365
7.
Cutting aluminum extrusion
When securing aluminum extrusions, use spacer blocks
or pieces of scrap as shown in
Fig. 59
to prevent defor-
mation of the aluminum. Use a cutting lubricant when
cutting the aluminum extrusion to prevent build-up of the
aluminum material on the blade.
WARNING:
•
Never attempt to cut thick or round aluminum
extrusions.
Thick or round aluminum extrusions can
be difficult to secure and may work loose during the
cutting operation which may result in loss of control and
serious personal injury.
Molding position
in Fig. 54 & 55
Bevel angle
Miter angle
52/38° type
45° type
52/38° type
45° type
For inside corner
(1)
Right 33.9°
Right 30°
Right 31.6°
Right 35.3°
(2)
Left 31.6°
Left 35.3°
For outside corner
(3)
(4)
Right 31.6°
Right 35.3°
Molding position
in Fig. 54 & 55
Molding edge against guide fence
Finished piece
For inside corner
(1)
Wall contact edge should be against
guide fence.
Finished piece will be on the Right
side of blade.
(2)
Ceiling contact edge should be
against guide fence.
For outside corner
(3)
Finished piece will be on the Left
side of blade.
(4)
Wall contact edge should be against
guide fence.
Molding position
in Fig. 54 & 55
Miter angle
Finished piece
For inside corner
(1)
Right 45°
Save the right side of blade
(2)
Left 45°
Save the left side of blade
For outside corner
(3)
Save the right side of blade
(4)
Right 45°
Save the left side of blade
Содержание LS1016L
