background image

4 ENGLISH

9. 

Always wear protective goggles to protect 

your eyes from injury when using power tools. 

The goggles must comply with ANSI Z87.1 in 

the USA, EN 166 in Europe, or AS/NZS 1336 

in Australia/New Zealand. In Australia/New 

Zealand, it is legally required to wear a face 

shield to protect your face, too.

It is an employer's responsibility to enforce 

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

Power tool use and care

1. 

Do not force the power tool. Use the correct 

power tool for your application.

 The correct 

power tool will do the job better and safer at the 

rate for which it was designed.

2. 

Do not use the power tool if the switch does 

not turn it on and off.

 Any power tool that cannot 

be controlled with the switch is dangerous and 

must be repaired.

3. 

Disconnect the plug from the power source 

and/or remove the battery pack, if detachable, 

from the power tool before making any adjust-

ments, changing accessories, or storing power 

tools.

 Such preventive safety measures reduce 

the risk of starting the power tool accidentally.

4. 

Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with 

the power tool or these instructions to operate 

the power tool.

 Power tools are dangerous in the 

hands of untrained users.

5. 

Maintain power tools and accessories. Check for 

misalignment or binding of moving parts, break-

age of parts and any other condition that may 

affect the power tool’s operation. If damaged, have 

the power tool repaired before use.

 Many accidents 

are caused by poorly maintained power tools.

6. 

Keep cutting tools sharp and clean.

 Properly 

maintained cutting tools with sharp cutting edges 

are less likely to bind and are easier to control.

7. 

Use the power tool, accessories and tool bits 

etc. in accordance with these instructions, tak-

ing into account the working conditions and 

the work to be performed.

 Use of the power tool 

for operations different from those intended could 

result in a hazardous situation.

8. 

Keep handles and grasping surfaces dry, 

clean and free from oil and grease.

 Slippery 

handles and grasping surfaces do not allow for 

safe handling and control of the tool in unexpected 

situations.

9. 

When using the tool, do not wear cloth work 

gloves which may be entangled.

 The entangle-

ment of cloth work gloves in the moving parts may 

result in personal injury.

Battery tool use and care

1. 

Recharge only with the charger specified by 

the manufacturer.

 A charger that is suitable for 

one type of battery pack may create a risk of fire 

when used with another battery pack.

2. 

Use power tools only with specifically desig

-

nated battery packs.

 Use of any other battery 

packs may create a risk of injury and fire.

3. 

When battery pack is not in use, keep it away 

from other metal objects, like paper clips, 

coins, keys, nails, screws or other small metal 

objects, that can make a connection from one 

terminal to another.

 Shorting the battery termi

-

nals together may cause burns or a fire.

4. 

Under abusive conditions, liquid may be ejected 

from the battery; avoid contact. If contact acci-

dentally occurs, flush with water. If liquid con

-

tacts eyes, additionally seek medical help.

 Liquid 

ejected from the battery may cause irritation or burns.

5. 

Do not use a battery pack or tool that is dam-

aged or modified.

 Damaged or modified batteries 

may exhibit unpredictable behaviour resulting in 

fire, explosion or risk of injury.

6. 

Do not expose a battery pack or tool to fire or 

excessive temperature.

 Exposure to fire or tem

-

perature above 130 °C may cause explosion.

7. 

Follow all charging instructions and do not 

charge the battery pack or tool outside the 

temperature range specified in the instruc

-

tions.

 Charging improperly or at temperatures 

outside the specified range may damage the 

battery and increase the risk of fire.

Service

1. 

Have your power tool serviced by a qualified 

repair person using only identical replacement 

parts.

 This will ensure that the safety of the power 

tool is maintained.

2. 

Never service damaged battery packs.

 Service 

of battery packs should only be performed by the 

manufacturer or authorized service providers.

3. 

Follow instruction for lubricating and chang-

ing accessories.

Cordless circular saw safety warnings

Cutting procedures

1. 

DANGER: Keep hands away from cutting area 

and the blade. Keep your second hand on auxil-

iary handle, or motor housing.

 If both hands are 

holding the saw, they cannot be cut by the blade.

2. 

Do not reach underneath the workpiece.

 The guard 

cannot protect you from the blade below the workpiece.

3. 

Adjust the cutting depth to the thickness of 

the workpiece.

 Less than a full tooth of the blade 

teeth should be visible below the workpiece.

4. 

Never hold the workpiece in your hands or 

across your leg while cutting. Secure the 

workpiece to a stable platform.

 It is important to 

support the work properly to minimise body expo

-

sure, blade binding, or loss of control.

Содержание HS011GM101

























Отзывы: