background image

13 ENGLISH

For tool with the ring

1

2

4
5

3

6

7

Fig.20

►    

1.

 Hex bolt 

2.

 Outer flange 

3.

 Circular saw blade 

4.

 Ring 

5.

 Inner flange 

6.

 Arrow on the circular saw 

blade 

7.

 Arrow on the tool

3.

  Press the shaft lock fully so that the circular saw 

blade cannot revolve and use the hex wrench to tighten 

the hex bolt.

1

2

3

4

Fig.21

►    

1.

 Shaft lock 

2.

 Hex wrench 

3.

 Loosen 

4.

 Tighten

To remove the circular saw blade, follow the installation 

procedure in reverse.

For tool with the inner flange for 

other than 15.88 mm hole-diameter 

saw blade

The inner flange has a certain diameter protrusion on one 

side of it and a different diameter protrusion on the other side. 

Choose a correct side on which protrusion fits into the saw 

blade hole perfectly. Mount the inner flange onto the mounting 

shaft so that the correct side of protrusion on the inner flange 

faces outward and then place saw blade and outer flange.

1

2

3

4

5

Fig.22

►    

1.

 Mounting shaft 

2.

 Inner flange 

3.

 Circular saw 

blade 

4.

 Outer flange 

5.

 Hex bolt

WARNING:

 

BE SURE TO TIGHTEN THE HEX 

BOLT CLOCKWISE SECURELY. Also be careful 

not to tighten the bolt forcibly. Slipping your hand 

from the hex wrench can cause a personal injury.

WARNING:

 

Make sure that the protrusion "a" 

on the inner flange that is positioned outside fits 

into the saw blade hole "a" perfectly.

 Mounting the 

blade on the wrong side can result in the dangerous 

vibration.

For tool with the inner flange for a 

15.88 mm hole-diameter saw blade 

(country specific)

Mount the inner flange with its recessed side facing 

outward onto the mounting shaft and then place circu-

lar saw blade (with the ring attached if needed), outer 

flange and hex bolt.

For tool without the ring

1

2

3

4

5

Fig.23

►    

1.

 Mounting shaft 

2.

 Inner flange 

3.

 Circular saw 

blade 

4.

 Outer flange 

5.

 Hex bolt

Содержание HS011GM101

























Отзывы: