22 ENGLISH
State of abnormality
Probable cause (malfunction)
Remedy
The vacuum cleaner does not run
along with the switch operation of
the tool.
The wireless unit is not installed into
the tool.
The wireless unit is improperly installed
into the tool.
Install the wireless unit correctly.
The terminal of the wireless unit and/or
the slot is dirty.
Gently wipe off dust and dirt on the terminal of the
wireless unit and clean the slot.
The wireless activation button on the
tool has not been pushed.
Push the wireless activation button briefly and make
sure that the wireless activation lamp is blinking
in blue.
The stand-by switch on the vacuum
cleaner is not set to “AUTO”.
Set the stand-by switch on the vacuum cleaner to
“AUTO”.
More than 10 tools are registered to the
vacuum cleaner.
Perform the tool registration again.
If more than 10 tools are registered to the vacuum
cleaner, the tool registered earliest will be cancelled
automatically.
The vacuum cleaner erased all tool
registrations.
Perform the tool registration again.
No power supply
Supply the power to the tool and the vacuum
cleaner.
The tool and vacuum cleaner are away
from each other (out of the transmission
range).
Get the tool and vacuum cleaner closer each other.
The maximum transmission distance is approxi
-
mately 10 m however it may vary according to the
circumstances.
Radio disturbance by other appliances
which generate high-intensity radio
waves.
Keep the tool and vacuum cleaner away from the
appliances such as Wi-Fi devices and microwave
ovens.
The vacuum cleaner runs while the
tool's switch trigger is not pulled.
Other users are using the wireless
activation of the vacuum cleaner with
their tools.
Turn off the wireless activation button of the other
tools or cancel the tool registration of the other
tools.
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
CAUTION:
Clean out the upper and lower
guards to ensure there is no accumulated saw
-
dust which may impede the operation of the lower
guarding system.
A dirty guarding system may limit
the proper operation which could result in serious
personal injury. The most effective way to accomplish
this cleaning is with compressed air.
If the dust is
being blown out of the guards, be sure the proper
eye and breathing protection is used.
CAUTION:
After each use, wipe off the saw
dust on the tool.
Fine saw dust may come inside the
tool and cause malfunction or a fire.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Adjusting 0°-cut accuracy
NOTICE:
Do not engage the levers for -1° bevel
angle when adjusting 0°-cut accuracy.
This adjustment has been made at the factory. But if it is
off, you can adjust it as the following procedure.
1.
Loosen the lever and the clamping screw on the
front and rear of the tool so that the bevel angle can be
changed.
2.
Make the base perpendicular to the blade using
a triangular rule or square rule by turning the adjusting
screw.
►
Fig.42:
1.
Triangular rule
2.
Adjusting screw for 0°
angle
3.
Tighten the lever and the clamping screw. After
that, make a test cut to check the verticalness.
Adjusting the depth guide
If the base does not slide up or down smoothly, the
depth guide may have been tilted. You can adjust the
depth guide as follows:
1. Make the base perpendicular, and set the depth of
cut to the deepest.
2. Loosen the adjusting screws for the depth guide.
The depth guide automatically adjusts its position.
3. Tighten the adjusting screws for the depth guide.
►
Fig.43:
1.
Adjusting screws for the depth guide
Содержание HS010GZ
