![background image](http://html1.mh-extra.com/html/makita/hs010gz/hs010gz_instruction-manual_4224270016.webp)
16 ENGLISH
Switch action
WARNING:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the “OFF” position when released.
WARNING:
NEVER defeat the lock-off button
by taping down or some other means.
A switch with
a negated lock-off button may result in unintentional
operation and serious personal injury.
WARNING:
NEVER use the tool if it runs when
you simply pull the switch trigger without press
-
ing the lock-off button.
A switch in need of repair
may result in unintentional operation and serious
personal injury. Return tool to a Makita service center
for proper repairs BEFORE further usage.
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
depress the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
►
Fig.9:
1.
Switch trigger
2.
Lock-off button
NOTICE:
Do not pull the switch trigger hard
without pressing in the lock-off button.
This can
cause switch breakage.
CAUTION:
The tool starts to brake the cir-
cular saw blade rotation immediately after you
release the switch trigger. Hold the tool firmly to
respond the reaction of the brake when releasing
the switch trigger.
Sudden reaction can drop the tool
off your hand and can cause a personal injury.
Adjusting depth of cut
CAUTION:
After adjusting the depth of cut,
always tighten the lever securely.
Loosen the lever on the depth guide and move the base
up or down. At the desired depth of cut, secure the base
by tightening the lever.
For cleaner, safer cuts, set cut depth so that no more
than one blade tooth projects below workpiece. Using
proper cut depth helps to reduce potential for danger
-
ous KICKBACKS which can cause personal injury.
►
Fig.10:
1.
Lever
NOTICE:
If the base doesn't slide up or down
smoothly, the depth guide may have been tilted. In
this case, adjust the depth guide (refer the section
about adjusting the depth guide).
Bevel cutting
CAUTION:
After adjusting the bevel angle,
always tighten the lever and clamping screw
securely.
Loosen the lever and the clamping screw. Set for the
desired angle by tilting accordingly, then tighten the
lever and the clamping screw securely.
►
Fig.11:
1.
Lever
2.
Clamping screw
Positive stopper
The positive stopper is useful for setting the designated
angle quickly. Turn the positive stopper so that the
arrow on it points your desired bevel angle (around
22.5°/45°/60°). Loosen the lever and the clamping
screw and then tilt the tool base until it stops. The posi
-
tion where the tool base stops is the angle you set with
the positive stopper. Tighten the lever and clamping
screw with the tool base at this position.
►
Fig.12:
1.
Positive stopper
-1°-bevel cutting
To perform -1°-bevel cutting, loosen the lever and the
clamping screw. Set the bevel angle to -1° while turning
the stopper lever in the direction of the arrow. After that,
tighten the lever and the clamping screw.
►
Fig.13:
1.
Stopper lever
Sighting
For straight cuts, align the 0° position on the front of the
base with your cutting line. For 45° bevel cuts, align the
45° position with it.
►
Fig.14:
1.
Cutting line (0° position)
2.
Cutting line
(45° position)
Lighting the lamp
CAUTION:
Do not look in the light or see the
source of light directly.
To turn on the lamp without running the tool, pull the
switch trigger without pressing the lock-off button.
To turn on the lamp with the tool running, press and hold
the lock-off button and pull the switch trigger.
The lamp goes out 10 seconds after releasing the
switch trigger.
►
Fig.15:
1.
Lamp
NOTE:
Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Electric brake
This tool is equipped with an electric blade brake. If the
tool consistently fails to quickly stop the circular saw
blade after switch lever release, have tool serviced at a
Makita service center.
CAUTION:
The blade brake system is not a
substitute for blade guard. NEVER USE TOOL
WITHOUT A FUNCTIONING BLADE GUARD.
SERIOUS PERSONAL INJURY CAN RESULT.
Electronic function
The tools equipped with electronic function are easy to
operate because of the following feature(s).
Soft start feature
Soft start because of suppressed starting shock.
Содержание HS010GZ
