9 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
HR005G
Capacities
Carbide-tipped bit
40 mm
Core bit
105 mm
No load speed (RPM)
250 - 500 min
-1
Blows per minute
1,450 - 2,900 min
-1
Overall length
with BL4025
484 mm
with BL4040
500 mm
Rated voltage
D.C. 36 V - 40 V max
Net weight
7.4 - 8.2 kg
•
Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
•
Specifications and battery cartridge may differ from country to country.
•
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi
-
est combinations, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
BL4020 / BL4025 / BL4040* / BL4050F*
* : Recommended battery
Charger
DC40RA / DC40RB / DC40RC
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above.
Use of any other battery cartridges
and chargers may cause injury and/or fire.
Recommended cord connected power source
Portable power pack
PDC01 / PDC1200
•
The cord connected power source(s) listed above may not be available depending on your region of residence.
•
Before using the cord connected power source, read instruction and cautionary markings on them.
Intended use
The tool is intended for hammer drilling and drilling in
brick, concrete and stone as well as for chiselling work.
Noise
The typical A-weighted noise level determined accord
-
ing to EN60745-2-6:
Sound pressure level (L
pA
) : 91 dB(A)
Sound power level (L
WA
) : 102 dB (A)
Uncertainty (K) : 3 dB(A)
NOTE:
The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE:
The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Содержание HR005G
