background image

 

CAUTION: 

• 

There is a tremendous and sudden twisting force 
exerted on the tool/bit at the time of hole 
break-through, when the hole becomes clogged 
with chips and particles, or when striking 
reinforcing rods embedded in the concrete. Always 
use the side grip (auxiliary handle) and firmly hold 
the tool by both side grip and switch handle during 
operations. Failure to do so may result in the loss 
of control of the tool and potentially severe injury. 

When drilling in concrete, granite, tile, etc., move the 
action mode changing lever to the position of

symbol 

to use "rotation with hammering" action. 
Be sure to use a tungsten-carbide tipped bit. 
Position the bit at the desired location for the hole, then 
pull the switch trigger. Do not force the tool. Light 
pressure gives best results. Keep the tool in position and 
prevent it from slipping away from the hole. 
Do not apply more pressure when the hole becomes 
clogged with chips or particles. Instead, run the tool at 
an idle, then remove the bit partially from the hole. By 
repeating this several times, the hole will be cleaned out 
and normal drilling may be resumed. 

 

Blow-out bulb (optional accessory) 

1

 

 

001302 

 
After drilling the hole, use the blow-out bulb to clean the 
dust out of the hole. 

 

Drilling operation 

When drilling in wood, metal or plastic materials, move 
the action mode changing lever to the position 
of

symbol to use "rotation only" action. 

Drilling in wood 

When drilling in wood, the best results are obtained with 
wood drills equipped with a guide screw. The guide 
screw makes drilling easier by pulling the bit into the 
workpiece. 

Drilling in metal 

To prevent the bit from slipping when starting a hole, 
make an indentation with a center-punch and hammer at 
the point to be drilled. Place the point of the bit in the 
indentation and start drilling. 
Use a cutting lubricant when drilling metals. The 

exceptions are iron and brass which should be drilled 
dry. 

 

CAUTION: 

• 

Pressing excessively on the tool will not speed up 
the drilling. In fact, this excessive pressure will only 
serve to damage the tip of your bit, decrease the 
tool performance and shorten the service life of the 
tool. 

• 

There is a tremendous force exerted on the tool/bit 
at the time of hole break through. Hold the tool 
firmly and exert care when the bit begins to break 
through the workpiece. 

• 

A stuck bit can be removed simply by setting the 
reversing switch to reverse rotation in order to back 
out. However, the tool may back out abruptly if you 
do not hold it firmly. 

• 

Always secure small workpieces in a vise or similar 
hold-down device. 

 

MAINTENANCE 

 

CAUTION: 

• 

Always be sure that the tool is switched off and 
unplugged before attempting to perform inspection 
or maintenance. 

To maintain product SAFETY and RELIABILITY, repairs, 
carbon brush inspection and replacement, any other 
maintenance or adjustment should be performed by 
Makita Authorized Service Centers, always using Makita 
replacement parts. 

 

ACCESSORIES 

 

CAUTION: 

• 

These accessories or attachments are 
recommended for use with your Makita tool 
specified in this manual. The use of any other 
accessories or attachments might present a risk of 
injury to persons. Only use accessory or 
attachment for its stated purpose. 

If you need any assistance for more details regarding 
these accessories, ask your local Makita Service Center. 

• 

Tungsten-carbide tipped hammer bit 

• 

Blow-out bulb 

• 

Safety goggles 

• 

Keyless drill chuck 13 

• 

Chuck key 

• 

Grip assembly 

• 

Depth gauge 

1. Blow-out bulb 

Содержание HP1630K









Отзывы: