7 ENGLISH
Work mode: disc sanding with normal side grip
Vibration emission (a
h, DS
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2
Work mode: disc sanding with anti vibration side grip
Vibration emission (a
h, DS
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2
Model GA9060R
Work mode: surface grinding with normal side grip
Vibration emission (a
h, AG
) : 6.5 m/s
2
Uncertainty (K) : 1.5 m/s
2
Work mode: surface grinding with anti vibration side grip
Vibration emission (a
h, AG
) : 6.0 m/s
2
Uncertainty (K) : 1.5 m/s
2
Work mode: disc sanding with normal side grip
Vibration emission (a
h, DS
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2
Work mode: disc sanding with anti vibration side grip
Vibration emission (a
h, DS
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2
NOTE:
The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE:
The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima
-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
WARNING:
The declared vibration emission
value is used for main applications of the power tool.
However if the power tool is used for other applica
-
tions, the vibration emission value may be different.
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
General power tool safety warnings
WARNING:
Read all safety warnings and
all instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Grinder safety warnings
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
1.
This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read
all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
2.
Operations such as polishing are not recom-
mended to be performed with this power tool.
Operations for which the power tool was not designed
may create a hazard and cause personal injury.
3.
Do not use accessories which are not specifically
designed and recommended by the tool manufac-
turer.
Just because the accessory can be attached to
your power tool, it does not assure safe operation.
4.
The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool.
Accessories running faster than
their rated speed can break and fly apart.
5.
The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool.
Incorrectly sized accessories
cannot be adequately guarded or controlled.
6.
Threaded mounting of accessories must match
the grinder spindle thread. For accessories
mounted by flanges, the arbour hole of the
accessory must fit the locating diameter of the
flange.
Accessories that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
7.
Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of the
rotating accessory and run the power tool at maxi-
mum no-load speed for one minute.
Damaged acces-
sories will normally break apart during this test time.
8.
Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments.
The eye protection must be capable of
stopping flying debris generated by various operations.
The dust mask or respirator must be capable of filtrating
particles generated by your operation. Prolonged expo
-
sure to high intensity noise may cause hearing loss.
9.
Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment.
Fragments of
workpiece or of a broken accessory may fly away and
cause injury beyond immediate area of operation.
10.
Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord.
Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
Содержание GA9060
Страница 2: ...1 Fig 1 A B C 2 1 Fig 2 1 Fig 3 Fig 4 1 2 3 Fig 5 1 2 3 4 Fig 6 1 2 Fig 7 1 4 2 3 Fig 8 2 ...
Страница 3: ...1 2 Fig 9 1 4 2 3 Fig 10 1 2 4 3 Fig 11 1 Fig 12 1 2 Fig 13 Fig 14 1 2 3 Fig 15 1 2 3 Fig 16 3 ...
Страница 4: ...Fig 17 1 2 3 4 Fig 18 1 2 3 4 ø45 ø78 ø78 5 Fig 19 1 Fig 20 1 Fig 21 1 2 Fig 22 1 Fig 23 4 ...
Страница 5: ...2 3 5 6 3 8 9 2 5 4 10 1 11 12 13 14 7 8 5 6 Fig 24 5 ...
