![background image](http://html1.mh-extra.com/html/makita/dls212/dls212_instruction-manual_4214158030.webp)
30 ENGLISH
Slide (push) cutting (cutting wide
workpieces)
WARNING:
Whenever performing a slide cut,
first pull the carriage full towards you and press
the handle all the way down, then push the car
-
riage toward the guide fence. Never start the cut
with the carriage not pulled fully toward you.
If
you perform the slide cut without the carriage pulled
fully toward you, unexpected kickback may occur and
serious personal injury may result.
WARNING:
Never attempt to perform a slide
cut by pulling the carriage towards you.
Pulling
the carriage towards you while cutting may cause
unexpected kickback resulting in possible serious
personal injury.
WARNING:
Never perform the slide cut with
the handle locked in the lowered position.
►
Fig.51:
1.
Stopper pin
1.
Unlock the stopper pin so that the carriage can
slide freely.
2.
Secure the workpiece with the proper type of vise.
3.
Pull the carriage toward you fully.
4.
Switch on the tool without the saw blade making
any contact and wait until the saw blade attains full
speed.
5.
Press the handle down and
push the carriage
toward the guide fence and through the workpiece.
6.
When the cut is completed, switch off the tool and
wait until the saw blade has come to a complete
stop
before returning the blade to its fully elevated
position.
Miter cutting
Refer to the section for adjusting the miter angle.
Bevel cut
WARNING:
After setting the blade for a bevel
cut, ensure that the carriage and saw blade will
have free travel throughout the entire range of the
intended cut before operating the tool.
Interruption
of the carriage or blade travel during the cutting oper-
ation may result in kickback and serious personal
injury.
WARNING:
While making a bevel cut, keep
hands out of the path of the saw blade.
The angle
of the blade may confuse the operator as to the actual
blade path while cutting and contact with the blade
will result in serious personal injury.
WARNING:
The saw blade should not be
raised until it has come to a complete stop.
During
a bevel cut, the piece cut off may come to rest against
the saw blade. If the blade is raised while it is rotating,
the cut-off piece may be ejected by the blade causing
the material to fragment which may result in serious
personal injury.
NOTICE:
When pressing down the handle, apply
pressure in parallel with the blade.
If a force is
applied perpendicularly to the turn base or if the pres-
sure direction is changed during a cut, the precision
of the cut will be impaired.
►
Fig.52
1.
Remove the upper fence on the side that you are
going to tilt the carriage.
2.
Unlock the stopper pin.
3.
Adjust the bevel angle according to the procedure
explained in the section for bevel angle adjustment.
Then tighten the knob.
4.
Secure the workpiece with a vise.
5.
Pull the carriage toward you fully.
6.
Switch on the tool without the blade making any
contact and wait until the blade attains full speed.
7.
Gently lower the handle to the fully lowered posi-
tion while applying pressure in parallel with the blade
and
push the carriage toward the guide fence to cut
the workpiece.
8.
When the cut is completed, switch off the tool and
wait until the blade has come to a complete stop
before returning the blade to its fully elevated position.
Compound cutting
Compound cutting is the process in which a bevel
angle is made at the same time in which a miter angle
is being cut on a workpiece. Compound cutting can be
performed at the angle shown in the table.
Miter angle
Bevel angle
Left and Right 0° - 45°
Left and Right 0° - 45°
When performing compound cutting, refer to the section
for press cutting, slide (push) cutting, miter cutting and
bevel cut.
Cutting base boards
CAUTION:
Make sure to use the horizontal
vise (optional accessory) when cutting the base
board.
CAUTION:
When cutting the workpiece of the
thickness 20 mm or thinner, make sure to use a
spacer block to secure the workpiece.
When cutting the base board in 45° miter angle, engage
the stopper lever to prevent the blade case from con-
tacting the base board. This will keep the clearance
between the base board and the blade case when the
carriage is fully pushed forward.
Refer to the SPECIFICATIONS for base board cutting
capacity.
►
Fig.53:
1.
Stopper lever
2.
Spacer block
3.
Horizontal vise
Содержание DLS212
