background image

17 ENGLISH

The overview of the wireless activation function 

setting is as follows. Refer to each section for detail 

procedures.

1.

 

Installing the wireless unit

2.

 

Tool registration for the vacuum cleaner

3.

 

Starting the wireless activation function

Installing the wireless unit

Optional accessory

CAUTION:

 

Place the tool on a flat and stable 

surface when installing the wireless unit.

NOTICE:

 

Clean the dust and dirt on the tool before 

installing the wireless unit.

 Dust or dirt may cause 

malfunction if it comes into the slot of the wireless unit.

NOTICE:

 

To prevent the malfunction caused by static, 

touch a static discharging material, such as a metal part 

of the tool, before picking up the wireless unit.

NOTICE:

 

When installing the wireless unit, always 

be sure that the wireless unit is inserted in the cor-

rect direction and the lid is completely closed.

1.

  Open the lid on the tool as shown in the figure.

1

►    

1.

 Lid

2.

 

Insert the wireless unit to the slot and then close 

the lid.

When inserting the wireless unit, align the projections 

with the recessed portions on the slot.

1

3

4

2

►    

1.

 Wireless unit 

2.

 Projection 

3.

 Lid 

4.

 Recessed 

portion

When removing the wireless unit, open the lid slowly. 

The hooks on the back of the lid will lift the wireless unit 

as you pull up the lid.

2

1

3

►    

1.

 Wireless unit 

2.

 Hook 

3.

 Lid

After removing the wireless unit, keep it in the supplied 

case or a static-free container.

NOTICE:

 

Always use the hooks on the back of 

the lid when removing the wireless unit.

 If the 

hooks do not catch the wireless unit, close the lid 

completely and open it slowly again.

Tool registration for the vacuum 

cleaner

NOTE:

 A Makita vacuum cleaner supporting the 

wireless activation function is required for the tool 

registration.

NOTE:

 Finish installing the wireless unit to the tool 

before starting the tool registration.

NOTE:

 During the tool registration, do not pull the 

switch trigger or turn on the power switch on the 

vacuum cleaner.

NOTE:

 Refer to the instruction manual of the vacuum 

cleaner, too.

If you wish to activate the vacuum cleaner along with 

the switch operation of the tool, finish the tool registra

-

tion beforehand.

1.

 

Install the batteries to the vacuum cleaner and the 

tool.

Содержание DHS783ZJU

























Отзывы: