![background image](http://html1.mh-extra.com/html/makita/dhs710zj/dhs710zj_instruction-manual_4109304006.webp)
6
ENGLISH (Original instructions)
Explanation of general view
SPECIFICATIONS
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
ENE078-2
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece. With
appropriate Makita genuine saw blades, other materials
can also be sawed.
General Power Tool Safety
Warnings
GEA010-1
WARNING Read all safety warnings and all
instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
CORDLESS CIRCULAR SAW
SAFETY WARNINGS
GEB061-4
Cutting procedures
1.
DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on
auxiliary handle, or motor housing.
If both hands
are holding the saw, they cannot be cut by the blade.
2.
Do not reach underneath the workpiece.
The guard
cannot protect you from the blade below the
workpiece.
3.
Adjust the cutting depth to the thickness of the
workpiece.
Less than a full tooth of the blade teeth
should be visible below the workpiece.
4.
Never hold piece being cut in your hands or
across your leg. Secure the workpiece to a stable
platform.
It is important to support the work properly
to minimize body exposure, blade binding, or loss of
control.
A typical illustration of proper hand support and
workpiece support. (Fig. 1)
5.
Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting tool may contact hidden wiring.
Contact
with a “live” wire will also make exposed metal parts of
the power tool “live” and could give the operator an
electric shock.
6.
When ripping, always use a rip fence or straight
edge guide.
This improves the accuracy of cut and
reduces the chance of blade binding.
7.
Always use blades with correct size and shape
(diamond versus round) of arbour holes.
Blades
that do not match the mounting hardware of the saw
will run eccentrically, causing loss of control.
8.
Never use damaged or incorrect blade washers or
bolt.
The blade washers and bolt were specially
1.
Red indicator
2.
Button
3.
Battery cartridge
4.
Battery indicator
5.
Overheat indicator
6.
Star marking
7.
Lever
8.
Front lever
9.
Rear wing nut
10. Stopper
11. Cutting line (0° position)
12. Cutting line (45° position)
13. Screw
14. Switch trigger
15. Lock-off lever
16. Hex wrench
17. Loosen
18. Tighten
19. Shaft lock
20. Mounting shaft
21. Inner flange
22. Saw blade
23. Outer flange
24. Hex bolt
25. Dust nozzle
26. Vacuum cleaner
27. Hose
28. Clamping lever
29. Rip fence (Guide rule)
30. Adjusting screw for 45°
31. Adjusting screw for 0°
32. Triangular rule
33. Base
34. Limit mark
35. Screwdriver
36. Brush holder cap
Model
DHS710
Blade diameter
185 - 190 mm
Max. cutting depth
at 0°
66 - 68.5 mm
at 45°
47.5 - 49 mm
at 50°
42.5 - 44 mm
No load speed (min
-1
)
4,800
Overall length
356 mm
Net weight
4.7 kg
Rated voltage
D.C. 36 V