9 ENGLISH
Rotation only
►
Fig.7:
1.
Rotation only
For drilling in wood, metal or plastic materials, depress
the lock button and rotate the action mode changing
knob to the
symbol. Use a twist drill bit or wood bit.
Hammering only
►
Fig.8:
1.
Hammering only
For chipping, scaling or demolition operations, depress
the lock button and rotate the action mode changing
knob to the
symbol. Use a bull point, cold chisel,
scaling chisel, etc.
CAUTION:
•
Do not rotate the action mode changing knob
when the tool is running. The tool will be
damaged.
•
To avoid rapid wear on the mode change mech-
anism, be sure that the action mode changing
knob is always positively located in one of the
three action mode positions.
Torque limiter
The torque limiter will actuate when a certain torque
level is reached. The motor will disengage from the out-
put shaft. When this happens, the bit will stop turning.
CAUTION:
•
As soon as the torque limiter actuates, switch
off the tool immediately. This will help prevent
premature wear of the tool.
•
Hole saws cannot be used with this tool. They
tend to pinch or catch easily in the hole. This
will cause the torque limiter to actuate too
frequently.
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and
the battery cartridge is removed before carrying
out any work on the tool.
Side grip (auxiliary handle)
►
Fig.9:
1.
Grip base
2.
Teeth
3.
Side grip
4.
Protrusion
5.
Loosen
6.
Tighten
CAUTION:
•
Always use the side grip to ensure operating
safety.
Install the side grip so that the teeth on the grip fit in
between the protrusions on the tool barrel. Then tighten
the grip by turning clockwise at the desired position. It
may be swung 360° so as to be secured at any position.
Bit grease
Coat the bit shank head beforehand with a small
amount of bit grease (about 0.5 -1 g). This chuck lubri
-
cation assures smooth action and longer service life.
Installing or removing the bit
Clean the bit shank and apply bit grease before install
-
ing the bit.
►
Fig.10:
1.
Bit shank
2.
Bit grease
Insert the bit into the tool. Turn the bit and push it in until
it engages.
►
Fig.11:
1.
Bit
2.
Chuck cover
If the bit cannot be pushed in, remove the bit. Pull the
chuck cover down a couple of times. Then insert the bit
again. Turn the bit and push it in until it engages.
After installing, always make sure that the bit is securely
held in place by trying to pull it out.
To remove the bit, pull the chuck cover down all the way
and pull the bit out.
►
Fig.12:
1.
Bit
2.
Chuck cover
Bit angle (when chipping, scaling or
demolishing)
►
Fig.13:
1.
Action mode changing knob
2.
O symbol
The bit can be secured at the desired angle. To change
the bit angle, depress the lock button and rotate the
action mode changing knob to the
O
symbol. Turn the
bit to the desired angle.
Depress the lock button and rotate the action mode
changing knob to the
symbol. Then make sure that
the bit is securely held in place by turning it slightly.
►
Fig.14
Depth gauge
►
Fig.15:
1.
Depth gauge
The depth gauge is convenient for drilling holes of
uniform depth. Loosen the side grip and insert the depth
gauge into the hole in the side grip. Adjust the depth
gauge to the desired depth and tighten the side grip.
NOTE:
•
The depth gauge cannot be used at the position
where the depth gauge strikes against the gear
housing.
Dust cup
►
Fig.16:
1.
Dust cup
Use the dust cup to prevent dust from falling over the
tool and on yourself when performing overhead drilling
operations. Attach the dust cup to the bit as shown in
the figure. The size of bits which the dust cup can be
attached to is as follows.
Bit diameter
Dust cup 5
6 mm - 14.5 mm
Dust cup 9
12 mm - 16 mm
Содержание DHR202
