background image

9 ENGLISH

Place the point of the driver bit in the screw head and 

apply pressure to the tool. Start the tool slowly and then 

increase the speed gradually. Release the switch trigger 

as soon as the clutch cuts in.

NOTE:

 When driving wood screw, pre-drill a pilot hole 

2/3 the diameter of the screw. It makes driving easier 

and prevents splitting of the workpiece.

Hammer drilling operation

CAUTION:

 

There is a tremendous and sud-

den twisting force exerted on the tool/drill bit 

at the time of hole breakthrough, when the hole 

becomes clogged with chips and particles, or 

when striking reinforcing rods embedded in the 

concrete.

First, turn the action mode changing ring so that the 
arrow on the tool body points to the 

 marking. The 

adjusting ring can be aligned in any torque levels for 

this operation.

Be sure to use a tungsten-carbide tipped drill bit.

Position the drill bit at the desired location for the hole, 

then pull the switch trigger. Do not force the tool. Light 

pressure gives best results. Keep the tool in position 

and prevent it from slipping away from the hole.

Do not apply more pressure when the hole becomes 

clogged with chips or particles. Instead, run the tool at 

an idle, then remove the drill bit partially from the hole. 

By repeating this several times, the hole will be cleaned 

out and normal drilling may be resumed.

Blow-out bulb

Optional accessory

1

Fig.14

►    

1.

 Blow-out bulb

After drilling the hole, use the blow-out bulb to clean the 

dust out of the hole.

Drilling operation

First, turn the adjusting ring so that the pointer points to 

the 

marking. Then proceed as follows.

Drilling in wood

When drilling in wood, the best results are obtained 

with wood drills equipped with a guide screw. The guide 

screw makes drilling easier by pulling the drill bit into 

the workpiece.

Drilling in metal

To prevent the drill bit from slipping when starting a 

hole, make an indentation with a center-punch and 

hammer at the point to be drilled. Place the point of the 

drill bit in the indentation and start drilling.

Use a cutting lubricant when drilling metals. The excep-

tions are iron and brass which should be drilled dry.

CAUTION:

 

Pressing excessively on the tool 

will not speed up the drilling.

 In fact, this excessive 

pressure will only serve to damage the tip of your drill 

bit, decrease the tool performance and shorten the 

service life of the tool.

CAUTION:

 

Hold the tool firmly and exert care 

when the drill bit begins to break through the 

workpiece.

 There is a tremendous force exerted on 

the tool/drill bit at the time of hole break through.

CAUTION:

 

A stuck drill bit can be removed 

simply by setting the reversing switch to reverse 

rotation in order to back out. However, the tool 

may back out abruptly if you do not hold it firmly.

CAUTION:

 

Always secure small workpieces 

in a vise or similar hold-down device.

CAUTION:

 

If the tool is operated continuously 

until the battery cartridge has discharged, allow 

the tool to rest for 15 minutes before proceeding 

with a fresh battery.

MAINTENANCE

CAUTION:

 

Always be sure that the tool is 

switched off and the battery cartridge is removed 

before attempting to perform inspection or 

maintenance.

NOTICE:

 

Never use gasoline, benzine, thinner, 

alcohol or the like. Discoloration, deformation or 

cracks may result.

Replacing carbon brushes

1

Fig.15

►    

1.

 Limit mark

Содержание DHP482SFX5













Отзывы: