18
ENGLISH
WIRELESS ACTIVATION
FUNCTION
What you can do w ith the w ireless
activation function
The wireless activation function enables clean and com
-
fortable operation. By connecting a supported vacuum
cleaner to the tool, you can run the vacuum cleaner
automatically along with the switch operation of the tool.
Fig.28
To use the wireless activation function, prepare follow
-
ing items:
A wireless unit (optional accessory)
A vacuum cleaner which supports the wireless
activation function
The overview of the wireless activation function
setting is as follows. Refer to each section for detail
procedures.
1.
Installing the wireless unit
2.
Tool registration for the vacuum cleaner
3.
Starting the wireless activation function
Installing the w ireless unit
Optional accessory
CAUTION:
Place the tool on a at and stable
surface w hen installing the w ireless unit.
NOTICE:
Clean the dust and dirt on the tool before
installing the w ireless unit.
Dust or dirt may cause
malfunction if it comes into the slot of the wireless unit.
NOTICE:
To prevent the malfunction caused by static,
touch a static discharging material, such as a metal part
of the tool, before picking up the w ireless unit.
NOTICE:
When installing the w ireless unit, alw ays
be sure that the w ireless unit is inserted in the cor-
rect direction and the lid is completely closed.
1.
Open the lid on the tool as shown in the figure.
Fig.29:
1.
Lid
2.
Insert the wireless unit to the slot and then close the lid.
When inserting the wireless unit, align the projections
with the recessed portions on the slot.
Fig.30:
1.
Wireless unit
2.
Projection
3.
Lid
4.
Recessed portion
When removing the wireless unit, open the lid slowly.
The hooks on the back of the lid will lift the wireless unit
as you pull up the lid.
Fig.31:
1.
Wireless unit
2.
Hook
3.
Lid
After removing the wireless unit, keep it in the supplied
case or a static-free container.
NOTICE:
Alw ays use the hooks on the back of
the lid w hen removing the w ireless unit.
If the
hooks do not catch the wireless unit, close the lid
completely and open it slowly again.
Tool registration for the vacuum
cleaner
NOTE:
A Makita vacuum cleaner supporting the
wireless activation function is required for the tool
registration.
NOTE:
Finish installing the wireless unit to the tool
before starting the tool registration.
NOTE:
During the tool registration, do not pull the
switch trigger or turn on the power switch on the
vacuum cleaner.
NOTE:
Refer to the instruction manual of the vacuum
cleaner, too.
If you wish to activate the vacuum cleaner along with
the switch operation of the tool, finish the tool registra
-
tion beforehand.
1.
Install the batteries to the vacuum cleaner and the
tool.
2.
Set the stand-by switch on the vacuum cleaner to
AUTO .
Fig.32:
1.
Stand-by switch
3.
Press the wireless activation button on the vac
-
uum cleaner for seconds until the wireless activation
lamp blinks in green. And then press the wireless acti
-
vation button on the tool in the same way.
Fig.33:
1.
Wireless activation button
2.
Wireless
activation lamp
If the vacuum cleaner and the tool are linked success
-
fully, the wireless activation lamps will light up in green
for seconds and start blinking in blue.
NOTE:
The wireless activation lamps finish blinking
in green after seconds elapsed. Press the wireless
activation button on the tool while the wireless acti
-
vation lamp on the cleaner is blinking. If the wireless
activation lamp does not blink in green, push the wire
-
less activation button briefly and hold it down again.
NOTE:
When performing two or more tool registra
-
tions for one vacuum cleaner, finish the tool registra
-
tion one by one.
Starting the w ireless activation
function
NOTE:
Finish the tool registration for the vacuum
cleaner prior to the wireless activation.
NOTE:
Refer to the instruction manual of the vacuum
cleaner, too.
After registering a tool to the vacuum cleaner, the
vacuum cleaner will automatically runs along with the
switch operation of the tool.
1.
Install the wireless unit to the tool.
2.
Connect the hose of the vacuum cleaner with the
tool.
Fig.34
3.
Set the stand-by switch on the vacuum cleaner to
AUTO .
Fig.35:
1.
Stand-by switch
Содержание DGA701
