![background image](http://html1.mh-extra.com/html/makita/df330dwex1/df330dwex1_instruction-manual_4255536007.webp)
7 ENGLISH
Speed change
►
Fig.5:
1.
Speed change lever
CAUTION:
Always set the speed change lever
fully to the correct position.
If you operate the
tool with the speed change lever positioned halfway
between the "1" side and "2" side, the tool may be
damaged.
CAUTION:
Do not use the speed change lever
while the tool is running.
The tool may be damaged.
Position of
speed
change lever
Speed
Torque
Applicable
operation
1
Low
High
Heavy load-
ing operation
2
High
Low
Light loading
operation
To change the speed, switch off the tool first. Select
the "2" side for high speed or "1" for low speed but high
torque. Be sure that the speed change lever is set to the
correct position before operation.
If the tool speed is coming down extremely during the
operation with "2", slide the lever to the "1" and restart
the operation.
Adjusting the fastening torque
►
Fig.6:
1.
Adjusting ring
2.
Graduation
3.
Arrow
The fastening torque can be adjusted in 19 levels by
turning the adjusting ring. Align the graduations with the
arrow on the tool body. You can get the minimum fas
-
tening torque at 1 and maximum torque at
marking.
The clutch will slip at various torque levels when set
at the number 1 to 18. The clutch does not work at
the
marking.
Before actual operation, drive a trial screw into your
material or a piece of duplicate material to deter-
mine which torque level is required for a particular
application.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/
drill bit
►
Fig.7:
1.
Sleeve
Turn the sleeve counterclockwise to open the chuck
jaws. Place the driver bit/drill bit in the chuck as far
as it will go. Turn the sleeve clockwise to tighten the
chuck. To remove the driver bit/drill bit, turn the sleeve
counterclockwise.
OPERATION
CAUTION:
Always insert the battery cartridge
all the way until it locks in place.
If not, it may
accidentally fall out of the tool, causing injury to you
or someone around you.
CAUTION:
When the speed comes down
extremely, reduce the load or stop the tool to
avoid the tool damage.
Hold the tool firmly with one hand on the grip and the
other hand on the bottom of the battery cartridge to
control the twisting action.
►
Fig.8
Screwdriving operation
CAUTION:
Adjust the adjusting ring to the
proper torque level for your work.
CAUTION:
Make sure that the driver bit is
inserted straight in the screw head, or the screw
and/or driver bit may be damaged.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the switch trigger
as soon as the clutch cuts in.
NOTE:
When driving wood screw, pre-drill a pilot hole
2/3 the diameter of the screw. It makes driving easier
and prevents splitting of the workpiece.
Drilling operation
First, turn the adjusting ring so that the arrow points to
the
marking. Then proceed as follows.
Drilling in wood
When drilling in wood, the best results are obtained
with wood drills equipped with a guide screw. The guide
screw makes drilling easier by pulling the drill bit into
the workpiece.
Drilling in metal
To prevent the drill bit from slipping when starting a
hole, make an indentation with a center-punch and
hammer at the point to be drilled. Place the point of the
drill bit in the indentation and start drilling.
Use a cutting lubricant when drilling metals. The excep
-
tions are iron and brass which should be drilled dry.
Содержание DF330DWEX1
Страница 2: ...1 2 Fig 1 1 Fig 2 1 Fig 3 A B 1 Fig 4 1 Fig 5 3 1 2 Fig 6 1 Fig 7 Fig 8 2 ...
Страница 3: ...Fig 9 1 2 Fig 10 Fig 11 Fig 12 3 ...
Страница 62: ...62 ...
Страница 63: ...63 ...