Makita DCM501, Инструкция по эксплуатации

Страница: 9 / 96

9
NOTE
• Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
OPERATION
CAUTION
To reduce the risk of scalding, follow the instructions
below:
• Do not remove the filter holder/cafe pod holder during
the brewing cycle. Steam builds up under the filter
holder/cafe pod holder.
• When the brewing section marked with is steaming,
do not touch it. ( Fig. L )
• Be aware that hot coffee drips from the bottom of the
filter holder/cafe pod holder even after the brewing
cycle.
• After the brewing is finished, wait at least 5 minutes
before removing the filter holder/cafe pod holder.
• If another brewing cycle is to be started, wait at least
5 minutes before supplying water to the appliance.
Otherwise, steam and hot water could be released and
scalding may result.
• Do not touch the plate on the bottom of the appliance
during and immediately after brewing.
NOTE
• For brewing, do not use any other liquid than water.
• Always use cold water for brewing. Hot water promotes
the dripping speed and cause overflow from the filter
holder/cafe pod holder.
• The maximum water tank capacity is 240ml. Do not
pour too much water to the water tank. Excess water
may come out of the overflow opening.
Brewing
1. Open the water tank lid and take the water tank out.
( Fig. C )
2. Pour preferred amount of fresh cold water into the
water tank and install it to the appliance. ( Fig. D )
Style
Recommended amount
of water
Ground coffee
(6.5 g *)
160 ml
Cafe pod
(60 mm type)
120 ml
* Equals to a level of the supplied spoon.
3. Close the water tank lid.
4. Remove the filter holder/cafe pod holder. ( Fig. E )
5. Follow the procedures below according to the style of
the coffee to be brewed :
Ground coffee ( Fig. F )
Open the cover. Take the filter out from the filter
holder. Put preferred amount of ground coffee into
the filter. Place the filter back in positon and close the
cover.
Cafe pod ( Fig. G )
Set a cafe pod into the cafe pod holder.
- Be sure that the flat surface of the cafe pod faces
up when placed.
- Do not use a torn cafe pod.
- Do not set two or more cafe pods. Hot water will
overflow.
6. Insert the filter holder/cafe pod holder to the slot on
the appliance.
If the holder/cafe pod holder cannot be inserted to the
slot properly, check if the filter/cafe pod is correctly
installed.
7. Put the cover on the coffee cup and place it on the
cup rest. ( Fig. H )
8. Press the power switch. The power lamp
lights up and brewing cycle begins. ( Fig. I )
The appliance will automatically turn off the
power when the brewing cycle is finished.
Press the power switch if you want to stop the brewing
in the middle.
Estimated time for brewing (160 ml)
Battery cartridge
(fully charged)
Estimated time
18 V
(with BL1830B)
approx. 5 min.
14.4 V
(with BL1430B)
approx. 5 min.
10.8 V - 12 V max
(with BL1041B)
approx. 7 min.
MAINTENANCE
WARNING
• When servicing is required, ask a Makita authorized
service center which deals genuine replacement parts.
Use of any other parts may create a hazard or cause
product damage.
• To avoid serious personal injury, always remove
the battery cartridge from the unit when cleaning or
performing any maintenance.
• Do not immerse the appliance and battery in water or
other liquids.
Daily cleaning
NOTICE
• Never use gasoline, benzine, thinner, alcohol or the like
when cleaning plastic parts. Discoloration, deformation
or cracks may result. After appliance cooled, use clean
clothes to remove dirt, dust, oil, grease etc.
• Do not use abrasive cleansers or scouring pads.
• Do not dry the inside of the appliance with a cloth, as
lint may remain.
Proper maintenance will ensure years of service for
your appliance. Clean the appliance after every use to
maintain quality coffee flavor.
1. Remove the battery from the appliance and allow the
appliance to cool.
2. Wipe the exterior with a soft cloth moistened with
water.
3. Remove the filter holder (with filter) or the cafe pod
holder from the appliance. Wash the removed parts
with soapy water. After that, rinse them with water.
4. Allow the appliance and all parts to dry completely.