11 ENGLISH
Using film type package
Preparing package for use
Cut off the tip of the package.
►
Fig.18
NOTICE:
Be sure to check the package for dam-
age before installation. Using the damaged pack-
age may cause malfunction.
Installing film type package to holder
1.
Pull the rod handle backward slowly until it stops.
►
Fig.19:
1.
Rod handle
2.
Insert the package into the holder.
3.
Attach the rubber ring, nozzle, and holder joint (as
a cap). Fasten the holder joint (as a cap) firmly.
►
Fig.20:
1.
Holder
2.
Film package
3.
Rubber ring
4.
Nozzle
5.
Holder joint (as a cap)
4.
Push the rod gently until the piston touches the package.
To remove the package, remove the holder joint (as a cap), nozzle,
rubber ring, and then push the rod handle forward until it stops.
Direct filling
1.
Push the rod handle all the way until it stops.
►
Fig.21:
1.
Rod handle
2.
Insert the tip of the holder into the caulking mate-
rial, and then pull the rod handle slowly to fill the holder
with the caulking material.
►
Fig.22:
1.
Holder
3.
Attach the rubber ring, nozzle, and holder joint (as
a cap). Fasten the holder joint (as a cap) firmly.
►
Fig.23:
1.
Holder
2.
Rubber ring
3.
Nozzle
4.
Holder
joint (as a cap)
Caulking operation
Pull the trigger to feed the caulking material. Put one hand
under the holder to support the tool while operating it.
NOTE:
You can rotate the holder in accordance with
required situations to facilitate the operation.
NOTE:
At the beginning of operation, set the speed
adjusting dial to "1" and pull the switch trigger slowly
to check how much amount of caulking material is fed.
NOTE:
Depending on the type and conditions of
caulking material, it may not be fed at low speed. In
this case, set the speed adjusting dial higher.
NOTE:
If the caulking material is not fed, check the
following points:
•
The tip of cartridge nozzle is not cut adequately.
•
The caulking material is solid and clogged in the nozzle.
•
The cartridge or package is damaged.
•
The caulking material is stiff. Warm the material
until it becomes soft.
•
The attached piston is not appropriate for the
type of caulking material.
After the operation, wipe off the caulking material from the tool.
Be sure to remove the caulking material before it becomes solid.
NOTE:
When the rod reaches front end, the motor
starts idling. Replace the caulking material when it
happens.
NOTE:
If you cannot pull out the rod, turn the speed
adjusting dial to 1, and pull the switch trigger for a
moment, and try to pull the rod out after the motor
stopped. If the rod is still clogged, perform the same
action until the rod is able to move.
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual.
The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard
-
ing these accessories, ask your local Makita Service
Center.
•
Piston
•
Holder set
• Nozzle
•
Makita genuine battery and charger
NOTE:
Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
Содержание DCG140ZXK
Страница 2: ...2 1 2 3 Fig 1 1 2 Fig 2 A B 1 2 Fig 3 1 Fig 4 1 Fig 5 1 Fig 6 1 2 5 3 4 6 8 7 Fig 7 1 2 3 Fig 8 ...
Страница 3: ...3 1 Fig 9 1 2 3 Fig 10 1 2 Fig 11 1 Fig 12 1 Fig 13 1 Fig 14 Fig 15 1 Fig 16 ...
Страница 4: ...4 1 2 3 Fig 17 Fig 18 1 Fig 19 1 2 3 4 5 Fig 20 1 Fig 21 1 Fig 22 1 2 3 4 Fig 23 ...
Страница 83: ...83 ...
