![background image](http://html1.mh-extra.com/html/makita/bux361/bux361_instruction-manual_4040701007.webp)
7
010823
Battery remaining capacity indicator (only
for models with Battery BL3622A)
Battery BL3622A is equipped with the battery remaining
capacity indicator.
(Fig. 7)
Press the CHECK button to indicate the battery remaining
capacity. The indicator lamps will then light for approx.
three seconds.
011713
• When only the lowermost indicator lamp (next to the
“E”) blinks, or when none of the indicator lamps light,
the battery capacity has run out, so the tool does not
operate. In these cases, charge the battery or replace
the empty battery with a fully charged one.
• When two or more indicator lamps do not light even
after charging is complete, the battery has reached the
end of its service life.
• When the upper two and lower two indicator lamps light
alternately, the battery may have malfunctioned.
Contact your local Makita authorized service center.
NOTE:
• The indicated capacity may be lower than the actual
level during use or immediately after using the tool.
• Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
ASSEMBLY
WARNING:
•
Always be sure that the tool is switched off and
battery cartridge is removed before carrying out
any work on the tool.
Failure to switch off and remove
the battery cartridge may result in serious personal
injury from accidental start-up.
•
Never start the tool unless it is completely
assembled.
Operation of the tool in a partially
assembled state may result in serious personal injury
from accidental start-up.
Installing the grip (Fig. 8)
Securely fit the barrier and grip onto the shaft pipe with
two screws and clamps.
Make sure that the grip/barrier assembly is located
between the spacer and the arrow mark. Do not remove
or shrink the spacer. Once assembled, do not remove the
barrier.
CAUTION:
• Never install the grip on the label or joint.
NOTE:
• In some countries, the barrier and spacer are not
provided with the tool. In that case, align the handle to
further side of the line which is indicated by the arrow
marks.
Mounting the attachment (Fig. 9)
To mount the attachment to a power unit:
1. Make sure that the lock lever is not tightened.
2. Align the pin with the arrow mark.
3. Insert the shaft into the drive shaft of the power unit
until the release button pops up.
4. Tighten the lock lever firmly as shown.
To remove the attachment, loosen the lock lever, press
the lock button and withdraw the shaft.
Status
Action to be taken
–
Blinking
Battery power has been nearly
used up.
Replace the battery with fully charged one.
–
Lighting On
Battery protector is shutting off
the power - battery power has
been used up.
Replace the battery with fully charged one.
Blinking
–
Overload protector is shutting off
the power - the motor was locked.
Release the switch trigger and remove the
cause of the motor lock or overload. If the
cutting tool is locked by entangling weeds or the
like, always remove the battery cartridge before
clearing it.
Lighting On
–
Overheat protector is shutting
off the power - overheating.
Rest the equipment for a while.
Blinking
Blinking
Electric or electronic malfunction
Ask your local authorized service center for
repairs.
Indicator lamps
Remaining capacity
Lighted
Off
Blinking
E
F
70% to 100%
45% to 70%
20% to 45%
0% to 20%
Charge the battery.
The battery may
have malfunctioned.
Содержание BUX361
Страница 2: ...2 1 012661 2 012942 3 010814 4 010825 5 010815 1 2 3 4 5 6 7 8 9 10 11 1 12 3 13 A B 14 15 16 1 2 ...
Страница 3: ...3 6 012967 7 011715 8 013202 9 012660 10 012761 11 012762 2 17 18 6 19 5 20 21 22 23 21 24 1 2 3 4 ...
Страница 72: ...ALA Makita Corporation Anjo Aichi Japan 885116A997 www makita com ...