Makita BTD042, Инструкция по эксплуатации

Страница: 7 / 72

7
Reversing switch action (Fig. 6)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
• When not operating the tool, always set the reversing
switch lever to the neutral position.
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for counter-
clockwise rotation. When the reversing switch lever is in
the neutral position, the switch trigger cannot be pulled.
Auto-stop mechanism (Fig. 7)
The tool stops automatically after the battery capacity
reaches under 20% to prevent the lack of fastening
torque. (Red color lamp lights on.) Charge the battery or
use a new fully charged one.
Auto-stop setting for number of impacts
This tool has a convenient auto-stop mechanism that
allows you to preset the desired number of impacts in
terms of the application. The tool then stops automati-
cally after reaching the preset number of impacts.
1. Pulling the trigger, insert the battery cartridge. Keep
on pulling the trigger after inserting the battery car-
tridge. (The indicating lamp on the back of the tool
will flash about 10 times, then the lamp will keep
lighting up lit.)
(Fig. 8)
2. Hit the tool housing around the grip once with a
screwdriver etc. (The indicating lamp will go out.)
(Fig. 9)
3. Release the trigger. (The indicating lamp will keep
lighting up lit for 0.5 seconds, then the lamp will go
out.)
(Fig. 10)
4. Hit the tool housing preset number of first digit
except 0. (The indicating lamp will light up in green
color. Then, the light goes out. )
Example: When the preset number is 12, hit the tool
housing once.
5. Pull the trigger, then release it.
6. Hit the tool housing preset number of second digit
except 0. (The indicating lamp will light up in red
color. Then, the light goes out.)
Example: When the preset number is 12, hit the tool
housing two times.
7. Pull the trigger, then release the trigger. (The indicat-
ing lamp will light up.)
8. Remove the battery cartridge. (Presetting has fin-
ished.) (The indicating lamp will go out.)
CAUTION:
When you change the presetting, do the same procedure
as above 1 – 8.
Confirming the presetting
Switch off the tool and insert the battery cartridge. The indicating lamp will indicate the presetting number.
Green lamp shows the first digit. Red lamp shows the second digit.
Example: Presetting number is 12.
Green color lamp flashes once.
ˆ
Red color lamp flashes two times.
ˆ
The lamp goes out.
Relation between presetting number and action
Indicating lamp
• After impacting preset numbers, the indicating lamp
lights in green color.
• The red color light will light on if the trigger is pulled
before the presetting number of impacts is achieved. It
indicates that the operation is incomplete.
Operation (Fig. 11, 12, 13 & 14)
[*1] Presetting number of impacts is impossible for more
than 200 impacts (4 seconds).
[*2] Fastening time includes when you pull the trigger
completely.
The proper fastening torque may differ depending upon
the kind or size of the screw/bolt, the material of the
workpiece to be fastened, etc. The relation between fas-
tening torque and fastening time is shown in
Fig. 11 & 13
for standard bolt or Fig. 12 & 14 for high tensile bolt.
Hold the tool firmly and place the point of the driver bit in
the screw head. Apply forward pressure to the tool to the
extent that the bit will not slip off the screw and turn the
tool on to start operation.
Presetting
number
Clockwise rotation Counterclockwise rotation
00 Auto-stop setting does not work. Auto-stop setting does not work.
01 – 99
After impacting [number of impacts
(presetting number x 2) x 0.02] seconds
ˆ
Green color lamp lights on.
Switch off before impacting [number of
impacts(presetting number x 2) x 0.02] sec-
onds
ˆ
Red color lamp lights on. Then, the lamp
will go out.
Auto-stop setting does not work. Indication
lamp goes out.