Makita BH341U/EBH341L Скачать руководство пользователя страница 24

Страница: 24 / 28

TROUBLESHOOTING

Before making a request for repairs, check a trouble for yourself. If any abnormality is found, control your machine according to the description

of this manual. Never tamper or dismount any part contrary to the description. For repairs, contact Authorized Service Agent or local dealership.

When the engine does not start after warm-up operation:

If there is no abnormality found for the check items, open the throttle by about 1/3 and start the engine.

State of abnormality

Probable cause (malfunction)

Remedy

Engine does not start

Failure to operate primer pump

Push 7 to 10 times

Low pulling speed of starter rope

Pull strongly

Lack of fuel

Feed fuel

Clogged fuel filter

Clean

Broken fuel tube

Straighten fuel tube

Deteriorated fuel

Deteriorated fuel makes starting more difficult.

Replace with new one. (Recommended
replacement: 1 month)

Excessive suction of fuel

Set throttle lever from medium speed to high
speed, and pull starter handle until engine
starts.

Once engine starts, cutter blade

starts rotating. Pay full attention to cutter

blade.

If engine will not start still, remove spark plug,
make electrode dry, and reassemble them as

they originally are. Then, start as specified.

Detached plug cap

Attach securely

Contaminated spark plug

Clean

Abnormal clearance of spark plug

Adjust clearance

Other abnormality of spark plug

Replace

Abnormal carburetor

Make request for inspection and maintenance.

Starter rope cannot be pulled

Make request for inspection and maintenance.

Abnormal drive system

Make request for inspection and maintenance.

Engine stops soon
Engine speed does not increase

Insufficient warm-up

Perform warm-up operation

Choke lever is set to “CLOSE” although
engine is warmed up.

Set to “OPEN”

Clogged fuel filter

Clean

Contaminated or clogged air cleaner

Clean

Abnormal carburetor

Make request for inspection and maintenance.

Abnormal drive system

Make request for inspection and maintenance.

Cutter blade does not rotate

Loosened cutter blade-tightening nut

Tighten securely

Twigs caught by cutter blade or dispersion-
preventing cover.

Remove foreign matter

Abnormal drive system

Make request for inspection and maintenance.

Main unit vibrates abnormally

Broken, bent or worn cutter blade

Replace cutter blade

Loosened cutter blade-tightening nut

Tighten securely

Shifted convex part of cutter blade and cutter

blade support fitting.

Attach securely

Abnormal drive system

Make request for inspection and maintenance.

Cutter blade does not stop immediately

High idling rotation

Adjust

Detached throttle wire

Attach securely

Abnormal drive system

Make request for inspection and maintenance.

Engine does not stop

Detached connector

Attach securely

Abnormal electric system

Make request for inspection and maintenance.

Stop engine immediately

Run engine at idling, and set choke lever
to CLOSE

Содержание BH341U/EBH341L





























Результаты поиска

Содержание BH341U/EBH341L

Отзывы:

Похожие инструкции для BH341U/EBH341L

Бренды по названию

Популярные бренды

Makita BH341U/EBH341L, Оригинальное руководство пользователя

Результаты поиска

Содержание BH341U/EBH341L

Отзывы:

Похожие инструкции для BH341U/EBH341L

Бренды по названию

Популярные бренды