Makita BCG180Z, Инструкция по эксплуатации

Страница: 7 / 56

7
Fig.6
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The lamp goes out approximately 10 seconds after the
switch trigger is released.
NOTE:
•
Use a dry cloth to wipe the dirt off the lens of lamp.
Be careful not to scratch the lens of lamp, or it
may lower the illumination.
•
When the tool is overheated, the lamp flickers.
Cool down the tool fully before operating again.
Drip preventive function
The motor keeps running for a short time even after the
trigger is released. It releases the pressure of the
caulking material and prevents dripping.
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out
any work on the tool.
•
Always place the tool on the ground or workbench
when carrying out any assembling work. The tool
without being held tight may loose balance and
cause injury.
Installing holder joint
Fig.7
Attach the holder joint firmly along the tool, set the plate,
and fix them with screws tightly.
To remove the holder joint, follow above procedure in
reverse.
NOTE:
•
There are two types of holders (optional
accessory), short holder (300ml) and long holder
(600ml). Use appropriate holder joint accordingly.
Installing rod and piston
Fig.8
Fig.9
Insert the rod into the slit of the tool.
Attach the piston and tighten it with a screw.
To remove the rod and piston, follow the installation
procedure in reverse.
NOTICE:
•
The teeth on the rod must point down.
•
There are three types of pistons. Piston A for
cartridges. Piston B for film type packs. Piston C
for direct filling.
•
Choose appropriate piston in accordance with the
type of caulking material container. Improper
piston may cause leakage or tool breakage.
•
There are two types of rods. The short rod for the
short holder (300ml), and the long rod for long
holder (600ml). Use appropriate rod in accordance
with holder type.
•
Always keep the rod and piston clean. Adhering
caulk may damage the tool.
Installing holder
Fig.10
Fig.11
Hold the bottom of the holder and the holder joint, then
turn the holder clockwise. Tighten it firmly until it stops.
Make sure the holder is tightened firmly. Otherwise the
tool may be damaged.
To remove the holder, turn it counter clockwise.
NOTE:
•
You can rotate the holder in accordance with
required situations to facilitate the operation.
•
The short holder (300ml) is intended for the
cartridges only. Use only piston A with short holder
(300ml), and do not use it with film type packs or
direct filling. Also use appropriate rod in
accordance with the holder type.
Installing cartridge
NOTICE:
•
Make sure the piston A is attached to the rod. Do
not use other type of piston for cartridge.
Installing the cartridge into the short holder (300ml)
Fig.12
Pull the rod handle backwards slowly until it stops.
Fig.13
Insert the cartridge into the holder as illustrated.
Push the rod gently until the piston touches the bottom
of the cartridge.
To remove the cartridge, pull the rod backwards until it
stops, then lift out the cartridge.
Installing the cartridge into the long holder (600ml)
Fig.14
Remove the holder cap from the holder.
Pull the rod handle backwards slowly until it stops.
Fig.15
Insert the cartridge into the holder.
Attach the holder cap. Make sure it is tightened firmly.
Push the rod gently until the piston touches the bottom
of the cartridge.
To remove the cartridge, remove the holder cap, then
take out the cartridge.
NOTICE:
•
Always check the cartridge for puncture or
damage before installing. Do not use damaged
cartridge, otherwise the tool may be damaged.
•
When using a partially used cartridge, remove any
adhered material on the cartridge.