Makita 9565CR, Инструкция по эксплуатации

Страница: 5 / 72

5
ENGLISH (Original instructions)
Explanation of general view
SPECIFICATIONS
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
ENE048-1
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
ENF002-2
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety
Warnings
GEA010-1
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
GRINDER SAFETY WARNINGS
GEB033-7
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
1. This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
2. Operations such as polishing are not
recommended to be performed with this power
tool.
Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
3. Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer.
Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool.
Accessories running faster than their rated
speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool.
Incorrectly sized accessories
cannot be adequately guarded or controlled.
6. Threaded mounting of accessories must match
the grinder spindle thread. For accessories
mounted by flanges, the arbour hole of the
accessory must fit the locating diameter of the
flange.
Accessories that do not match the mounting
1. Shaft lock
2. Slide switch
3. Indication lamp (speed adjusting
dial)
4. Indication lamp
5. Speed adjusting dial
6. Wheel guard
7. Bearing box
8. Screw
9. Lever
10. Lock nut
11. Depressed center grinding wheel/
Multi-disc
12. Inner flange or super flange
13. Lock nut wrench
14. Abrasive disc
15. Rubber pad
16. Marking A
17. Marking B
18. Marking C
19. Pin
20. Vent
21. Wire cup brush/Wire bevel brush
22. Abrasive cut-off wheel/diamond
wheel
23. Inner flange
24. Wheel guard for abrasive cut-off
wheel/diamond wheel
25. Abrasive cut-off wheel (Thinner
than 4 mm (5/32”))
26. Abrasive cut-off wheel (4 mm (5/
32”) or thicker)
27. Diamond wheel (Thinner than 4 mm
(5/32”))
28. Diamond wheel (4 mm (5/32”) or
thicker)
29. Exhaust vent
30. Inhalation vent
Model 9565CR 9565CVR
Wheel diameter 125 mm 125 mm
Max. wheel thickness 7.2 mm 7.2 mm
Spindle thread M14 M14
Rated speed (n)/No load speed (
n
0
) 12,000 min
-1
12,000 min
-1
Overall length 299 mm 299 mm
Net weight 2.4 kg 2.4 kg
Safety class /II