![background image](http://html.mh-extra.com/html/makita/6407/6407_instruction-manual_224885003.webp)
ENGLISH
Explanation of general view
1
Chuck
2
Chuck key
3
Tighten
4
Sleeve
5
Ring
6
Switch trigger
7
Lock button
8
Reversing switch lever
SPECIFICATIONS
Model
6407/6408
Drilling capacities
Steel ............................................................ 10 mm
Wood ........................................................... 25 mm
No load speed (RPM) ................................ 0 – 2,500
Overall length ............................................... 261 mm
Net weight ....................................................... 1.4 kg
• Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
• Note: Specifications may differ from country to
country.
Power supply
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
These symbols mean:
Read instruction manual.
DOUBLE INSULATION
ADDITIONAL SAFETY RULES
1. Always be sure you have a firm footing.
Be sure no one is below when using the
machine in high locations.
2. Hold the machine firmly.
3. Keep hands away from rotating parts.
4. When drilling into walls, floors or wherever
‘‘live’’ electrical wires may be encountered, DO
NOT TOUCH ANY METAL PARTS OF THE
MACHINE!
Hold the machine by the insulated grasping
surfaces to prevent electric shock if you drill
into a ‘‘live’’ wire.
5. Do not leave the machine running. Operate the
machine only when hand-held.
6. Do not touch the drill bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing drill bit
Important:
Always be sure that the machine is switched off and
unplugged before installing or removing the bit.
For 6407 (Fig. 1)
To install the bit, place it in the chuck as far as it will
go. Tighten the chuck by hand. Place the chuck key in
each of the three holes and tighten clockwise. Be sure
to tighten all three chuck holes evenly.
To remove the bit, turn the chuck key counterclock-
wise in just one hole, then loosen the chuck by hand.
After using the chuck key, remember to return it to the
chuck key holder.
For 6408 (Fig. 2)
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the bit in the chuck as far
as it will go. Hold the ring firmly and turn the sleeve
clockwise to tighten the chuck.
To remove the bit, hold the ring and turn the sleeve
counterclockwise.
Switch action (Fig. 3)
CAUTION:
Before plugging in the machine, always check to see
that the switch trigger actuates properly and returns to
the ‘‘OFF’’ position when released.
To start the machine, simply pull the trigger. Machine
speed is increased by increasing pressure on the
trigger. Release the trigger to stop. For continuous
operation, pull the trigger and then push in the lock
button. To stop the machine from the locked position,
pull the trigger fully, then release it.
Reversing switch action (Fig. 4)
CAUTION:
• Always check the direction of rotation before drilling.
• Use the reversing switch lever only after the
machine comes to a complete stop. Changing the
direction of rotation before the machine stops may
damage the machine.
This machine has a reversing switch to change the
direction of rotation. Move the reversing switch lever
to the
position for clockwise rotation or the
posi-
tion for counterclockwise rotation.
6407/6408 (E)(’97. 5. 21)
3
Содержание 6407
