Makita 5903R, Инструкция по эксплуатации

Страница: 5 / 60

5
ENGLISH
(Original instructions)
Explanation of general view
1 Lever
2 Clamping screw
3 Base plate
4 Top guide
5 Base
6 60° angle cuts
7 45° angle cuts
8 30° angle cuts
9 Straight cuts
10 Blade
11 Setting protuberances
12 Hex socket head bolt
(For adjusting riving knife)
13 Cutting depth
14 Lock-off button
15 Switch trigger
16 Hex wrench
17 Shaft lock
18 Hex socket head bolt
19 Outer flange
20 Saw blade
21 Inner flange
22 Vacuum cleaner
23 Limit mark
24 Screwdriver
25 Brush holder cap
SPECIFICATIONS
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2014
ENE078-2
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and miter cuts with angles in
wood while in firm contact with the workpiece. With
appropriate Makita genuine saw blades, other materials
can also be sawed.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
For model 5705R
ENF100-1
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.37 Ohms it can be presumed that
there will be no negative effects. The mains socket used
for this device must be protected with a fuse or protective
circuit breaker having slow tripping characteristics.
GEA010-2
General power tool safety warnings
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
GEB143-1
CIRCULAR SAW SAFETY WARNINGS
Cutting procedures
1.
DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on auxil-
iary handle, or motor housing.
If both hands are
holding the saw, they cannot be cut by the blade.
2. Do not reach underneath the workpiece. The
guard cannot protect you from the blade below the
workpiece.
3. Adjust the cutting depth to the thickness of the
workpiece.
Less than a full tooth of the blade teeth
should be visible below the workpiece.
4. Never hold the workpiece in your hands or
across your leg while cutting. Secure the work-
piece to a stable platform.
It is important to sup-
port the work properly to minimise body exposure,
blade binding, or loss of control.
(Fig. 1)
Model 5705R 5903R 5103R 5143R
Blade diameter 190 mm 235 mm 270 mm 355 mm
Max.
cutting depth
at 90° 66 mm 85 mm 100 mm 130 mm
at 45° 46 mm 64 mm 73 mm 90 mm
No load speed (min
–1
) 4,800 4,500 3,800 2,700
Overall length 356 mm 400 mm 442 mm 607 mm
Net weight 5.4 kg 7.2 kg 9.3 kg 12.5 kg
Safety class /II /II /II /II