Makita 4350T, Инструкция по эксплуатации

Страница: 8 / 52

8 ENGLISH
Number on adjusting dial
4 - 5
Mild steel 3 - 5
Stainless steel 3 - 4
Aluminum 3 - 5
Plastics 1 - 4
Workpiece to be cut
Wood
CAUTION:
• The speed adjusting dial can be turned only as far
as 5 and back to 1. Do not force it past 5 or 1, or
the speed adjusting function may no longer work.
The tools equipped with electronic function are easy to
operate because of the following features.
Constant speed control
Electronic speed control for obtaining constant speed.
Possible to get fine finish, because the rotating speed is
kept constant even under load condition.
Soft start feature
Safety and soft start because of suppressed starting shock.
Lighting up the lamps
For 4350FCT only
CAUTION:
• Do not look in the light or see the source of light
directly.
To turn on the lamp, pull the trigger. Release the trigger
to turn it off.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of
lamp. Be careful not to scratch the lens of lamp,
or it may lower the illumination.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing or removing saw blade
CAUTION:
• Always clean out all chips or foreign matter
adhering to the blade and/or blade holder. Failure
to do so may cause insufficient tightening of the
blade, resulting in a serious personal injury.
• Do not touch the blade or the workpiece imme -
diately after operation; they may be extremely
hot and could burn your skin.
• Tighten the saw blade securely. Failure to do so
may cause a serious injury.
• When you remove the saw blade, be careful not
to hurt your fingers with the top of the blade or
the tips of workpiece.
To install the blade, open the tool opener to the position
shown in the figure.
►
Fig.4: 1.
Tool opener
Keeping that situation, insert the saw blade into the blade clamp
as far as the two protrusions of the blade can not be seen.
► Fig.5: 1. Blade clamp 2. Jig saw blade
3. Protrusions
Return the tool opener to its original position.
After installing, always make sure that the blade is
securely held in place by trying to pull it out.
CAUTION:
• Do not open the tool opener excessively, or it
may cause tool damage.
To remove the blade, open the tool opener to the position
shown in the figure. Pull the saw blade out toward the base.
► Fig.6: 1. Jig saw blade
NOTE:
• Occasionally lubricate the roller.
Hex wrench storage
► Fig.7: 1. Base 2. Hex wrench
When not in use, the hex wrench can be conveniently stored.
OPERATION
CAUTION:
• Hold the tool firmly with one hand on the main
handle when performing the tool. If necessary,
the front part of the tool may be supported by
the other hand.
• Always hold the base flush with the workpiece.
Failure to do so may cause blade breakage,
resulting in a serious injury.
► Fig.8: 1. Cutting line 2. Base
Turn the tool on and wait until the blade attains full speed.
Then rest the tool base flat on the workpiece and gently
move the tool forward along the previously marked cutting
line. When cutting curves, advance the tool very slowly.
Bevel cutting
CAUTION:
• Always be sure that the tool is switched off and
unplugged before tilting the base.
With the base tilted, you can make bevel cuts at any
angle between 0° and 45° (left or right).
► Fig.9
Loosen the bolt on the back of the base with the hex
wrench. Move the base so that the bolt is positioned in
the center of the bevel slot in the base.
► Fig.10: 1. Base 2. Bolt 3. Hex wrench
Tilt the base until the desired bevel angle is obtained. The
V-notch of the gear housing indicates the bevel angle by
graduations. Then tighten the bolt firmly to secure the base.
► Fig.11: 1. Graduation 2. Bevel slot 3. Base 4. Gear
housing
5.
V-notch
6.
Bolt