background image

MAK

E

R

B

OT

 M

E

TH

O

D

 MAN

U

AL

PA

G

E

 5

Safety alert symbols precede each safety message in this 
manual. These symbols indicate potential safety hazards that 
could harm you or others or cause product or property damage.

Warning: 

The MakerBot Method includes moving parts that may cause injury. Never reach inside the 

MakerBot Method while it is in operation.

Warning:

 The MakerBot Method generates high temperatures. Always allow the MakerBot Method 

Performance Extruders to cool down before you reach inside.

Warning:

 There is a risk of shock. The electronics of the MakerBot Method are not user serviceable.

Caution:

 Do not print using materials that have not been approved by MakerBot for use with the 

MakerBot Method.

Caution:

 The socket outlet must be located near the printer and must be easily accessible.

Caution: 

In case of emergency, disconnect the MakerBot Method from the socket outlet.

Caution:

 The MakerBot Method melts plastic during printing. Plastic odors and particles may be 

emitted during this operation. Make sure to set up the MakerBot Method in a well-ventilated area.

Caution:

 Always allow the Performance Extruders to cool to 50°C before reaching inside the 

MakerBot Method or removing the Performance Extruders.

Caution:

 Children under 12 should be supervised by an adult. 

Caution:

 Dust generation and accumulation should be minimized. Some dust and dry powders can 

build static electricity charges when subjected to friction and create an ignition hazard.

Note:

 For users in Japan, the power cord is only for use with this printer model, the MakerBot Method 

Performance 3D Printer.

Содержание METHOD
























Отзывы: