background image

Coloured flashes of light

Behind the seventh door you’ll find another 
cable. Now build your circuit and insert 
the red LED. Pay attention to the direction 
of installation! The red LED appears to 
be installed the wrong way around, i.e. 
with the cathode towards the positive 
pole of the battery. Using the button, you 
can alternately charge (contact open) or 
discharge (contact closed). When charging, 
a green flash of light is generated, when 
discharging, a red light appears. You 
can repeat the alternating charging and 
discharging as often as you like. Each time 
you press the button, a red flash will appear; 
once you release it, a green flash will appear. 

Your battery delivers direct 
current. This means that 
the current always flows 
in the same direction. In 
your circuit, however, an 
alternating current is created 
when activating your push 
button. In one direction 
the green LED shines, in 
the other direction the red 

one will shine. Therefore, both LEDs in this 
circuit had to be installed with different 
directions. 

7

The PTC fuse

All your experiments are 
secured by a fuse to help 
if a mistake occurs. If you 
accidentally short-circuit a 
cable, it could become glowing 
hot, or the battery could heat 
up, break, or even explode. But 
the fuse will prevent that from 
happening.

Many fuses just blow when you 
cause a short circuit. You will 
then need a new fuse. But your 
special fuse is different. This is 
a self-resetting fuse, also known 
as a PTC fuse. If too much 
current flows during a short-
circuit, the PTC fuse becomes 
hot and lets only a little current 

through because its resistance 
rises sharply. That’s where 
the name comes from. PTC 
stands for “Positive Temperature 
Coefficient” and means that 
the resistance increases as 
the temperature rises. If you 
then switch off the power and 
eliminate the fault, it cools down 
and is as good as new again.

Please do not try it out, as the battery 

will quickly become unusable in the

 

event of a short circuit. Also, the PTC 

fuse can reach about 60 degrees

 

and can easily burn your fingers. But 

that would still be better than glowing

 

wires and exploding batteries. So

 

always remember: The safety device

 

is only there for emergencies, similar

 

to the emergency brake on a train.

Attention!

Содержание 1968203





























Отзывы: