Makel MSA-CM Series Скачать руководство пользователя страница 14

Страница: 14 / 48

4 Detailed Functions Description

Table 3: General configurations' parameters description

Parameter

Description

Values

Manual Mode usage

Selects if the device can be set to Manual
Mode operation via Manual Mode button and
via

Maintenance Mode

Possible values:

Use

Not used

Use Time Limited Manual mode?

Should the Manual Mode operation terminate
automatically after a certain amount of time?

Possible values:

Yes

Duration

Amount of time after which the Manual Mode
operation should be automatically terminated.

Possible values:
*5min
10min
…
1h15min

Send Status Ind. In Manual
mode?

If this parameter is set to “Yes”, then, even in
Manual Mode the device will send the
channels' status to the bus.

Possible values:
No
*Yes

Output

[x]

and

[x+1]

function

Selects the function of a pair of channels.

Possible values:
*Lighting
Shutters and Blinds

It's convenient to explain in more detail some of the parameters present in the General configurations'

page. The

“Use Time Limited Manual mode?”

if set to “No”, once the device enters in Manual Mode

by pressing Manual Mode button or by sending message via

“Maintenance Mode”

CO it will leave

that mode just by pressing again the Manual Mode button or be sending message to the CO. However, if

the parameter is set to “Yes” the parameter

“Duration”

is shown; When the device is set to Manual Mode

via Manual Mode button or via CO it will leave this mode if the amount of time set in “Duration”

parameter expires or if Manual Mode button is again pressed or message is sent to the

“Maintenance

Mode”

CO.

The parameter

“Send Status Ind. In Manual mode?”

when set to “Yes” will allow the device to, when

in Manual Mode, send the channels status to the bus (all the incoming messages to device will still be

ignored). When set to “No” the device wont send the channels' status to the bus.

The

“Manual Mode usage”

, when configured to “Use” will make available one Communication Object:

[input] “General – Maintenance Mode”

: Sending “True” sets the device to

maintenance mode.

Visible if

“Manual Mode usage”

is set to “Use”

Visible if

“Use Time Limited Manual mode”

is set to “Yes”

Visible if

“Manual Mode usage”

is set to “Use”

User’s Manual

Page 14

Содержание MSA-CM Series

















































Результаты поиска

Содержание MSA-CM Series

Отзывы:

Бренды по названию

Популярные бренды

Makel MSA-CM Series, Руководство пользователя

Результаты поиска

Содержание MSA-CM Series

Отзывы:

Бренды по названию

Популярные бренды