manualshive.com logo in svg

Major SYNERGY MJ62-170, Руководство оператора и список запасных частей

Поделиться
Скачать
Major SYNERGY MJ62-170 Скачать руководство пользователя страница 19

www.major-equipment.com

15

Operating the Machine/Mowing

Never place limbs under the machine while rotors are turning. Rotors can remain turning for up to 1 minute 

after disengaging PTO.

While operating this machine the PTO input rate should not exceed the RPM stated in the Product 

Specifications section of this booklet. Always operate on level ground when connecting/disconnecting the 

implement. This will prevent dangerous movement.

Never allow anyone to stand between the tractor and the machine. Ensure the machine is attached correctly 

to the tractor as previously described. Always start up the tractor PTO at a low RPM. Build up to operating 

speed, select a suitable forward gear & proceed to cut grass.

1. 

Hitch the machine as outlined in the previous section. Ensure bystanders are clear from the machine & cannot be 

hit with debris expelled from the machine. 

2.  Check PTO shaft is fully engaged on tractor PTO splines.  

3.  Lower the machine by hydraulic control to the ground or use tractor linkage controls.

4.  Start up the tractor PTO at a low RPM.

5. 

Build up to operating speed, select a suitable forward gear & proceed to cut grass.

Mowing Position

Содержание SYNERGY MJ62-170











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды