Major Science MC-0203 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 58

Major Science MC-0203 Скачать руководство пользователя страница 49

48

Section 7 Troubleshooting Guide

Many operating problems may be solved by carefully reading and following the
instructions in this manual accordingly. Some suggestions for troubleshooting
are given below. Should these suggestions not resolve the problem, contact
our SERVICE DEPARTMENT or a distributor in your region for assistance. If
troubleshooting service is required, please include a full description of the
problem.

7.1 Problem and Solution

Problem

Recommendations

No signal on the screen

1. Check the

FUSE

2. Ensure that the AC power switch is ON

3. Check the three-pronged power cord are properly plugged into a

grounded three-prong AC outlet with the appropriate voltage

Fan Error

Contact our service department or a distributor in your region.

7.2 Maintenance

Mini cooler may be cleaned with a moist cloth containing a mild soap solution.
The chamber and blocks are constructed of aluminum alloy and may be
cleaned with any of the commercial aluminum cleaners on the market

DOMINIQUE DUTSCHER SAS

«
...
47
48
49
50
51
...
»

Содержание MC-0203



























































Отзывы:

Нет отзывов