background image

54D5032 

3

4.  Never install the fireplace 

    •  in a recreational vehicle

    •  where curtains, furniture, clothing, or other flammable 

objects are less than 42" from the front, top, or sides 

of the fireplace

    •  in high traffic areas

    •  in windy or drafty areas 
5.  This fireplace reaches high temperatures. Keep children 

and adults away from hot surfaces to avoid burns or cloth

-

ing ignition. Fireplace will remain hot for a time after 

shutdown. Allow surfaces to cool before touching. 

6.  Carefully supervise young children when they are in the 

room with fireplace. 

7.  Do not modify fireplace under any circumstances. Any 

parts removed for servicing must be replaced prior to 

operating fireplace. 

8.  Turn fireplace off and let cool before servicing, install

-

ing, or repairing. Only a qualified service person should 

install, service, or repair the fireplace. Have burner system 

inspected annually by a qualified service person. 

9.  You must keep control compartments, burners, and cir

-

culating air passages clean. More frequent cleaning may 

be needed due to excessive lint and dust. Turn off the gas 

valve and pilot light before cleaning fireplace. 

10.  Have venting system inspected annually by a qualified 

service person. If needed, have venting system cleaned 

or repaired. See 

Cleaning and Maintenance

, page 39. 

11.  Keep the area around your fireplace clear of combustible 

materials, gasoline, and other flammable vapor and liq

-

uids. Do not run fireplace where these are used or stored. 

Do not place items such as clothing or decorations on or 

around fireplace. 

INSTALLER

Please leave these instructions with the appliance.

OWNER

Please retain these instructions for future reference

.

IMPORTANT SAFETy INFORMATION

This fireplace is a vented product. This fireplace must be 

properly installed by a qualified service person. The glass door 

must be properly seated and sealed. If this unit is not properly 

installed by a qualified service person with glass door properly 

seated and sealed, combustion leakage can occur. 

CARBON  MONOxIDE  POISONING:

 

Early  signs  of 

carbon monoxide poisoning are similar to the flu with head

-

aches, dizziness and/or nausea. If you have these signs, the 

fireplace may not have been installed properly. Get fresh air 

at once! Have the fireplace inspected and serviced by a quali

-

fied service person. Some people are more affected by carbon 

monoxide than others. These include pregnant women, people 

with heart or lung disease or anemia, those under the influence 

of alcohol, and those at high altitudes. 
Propane/LP gas and natural gas are both odorless. An odor-

making agent is added to each of these gases. The odor helps 

you detect a gas leak. However, the odor added to these gases 

can fade. Gas may be present even though no odor exists.
Make certain you read and understand all warnings. Keep 

this manual for reference. It is your guide to safe and proper 

operation of this fireplace.
1.  This appliance is only for use with the type of gas indi

-

cated on the rating plate. This appliance is not convertible 

for use with other gases unless a certified kit is used. 

2.  For propane/LP fireplace, do not place propane/LP supply 

tank(s) inside any structure. Locate propane/LP supply 

tank(s) outdoors. To prevent performance problems, do 

not use propane/LP fuel tank of less than 100 lbs. capac

-

ity. 

3.  If you smell gas

    •  shut off gas supply.

    •  do not try to light any appliance.

    •  do not touch any electrical switch; do not use any 

phone in your building .

    •  immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.

Continued on page 4

• Read this owner’s manual carefully and completely before trying to assemble, operate, 

or service this fireplace. 

• Any change to this fireplace or its controls can be dangerous.
• Improper installation or use of this fireplace can cause serious injury or death from 

fire, burns, explosions, electrical shock and carbon monoxide poisoning.

W

ARNING

Содержание 300DVBH





















































Отзывы: