background image

22

DVRTSB Bay Window Fireplace

10003848 

It is necessary to periodically clean glass. During start-
up condensation, which is normal, forms on the inside 
of the glass. This condensation causes lint, dust and 
other airborne particles to cling to glass surface.
Also initial paint curing may deposit a slight film on the 
glass. It is therefore recommended glass be cleaned 
two or three times with a non-ammonia based house-
hold cleaner and warm water (We recommend gas 
fireplace glass cleaner) within the first few weeks of 
operation.
After the initial cleaning process the glass should be 
cleaned two or three times during each operating 
season depending on the environment in the house.

Clean the glass after the first two weeks of 
operation.

Installation of Logs

Handle and dispose of the plastic bags in a 
safe manner. They are not toys and should 
be kept away from infants.

Ceramic Refractory Installation

Glass Cleaning

The rear wall refractory panels are installed in the unit 
prior to shipment.
1.  Unpack the ceramic refractory panels from their 

carton.

Handle the refractory material carefully, the 
panels are fragile.

2.  Place the front floor refractory panels on the base  

of the fireplace. (Fig. 38)

3.  Place both side panels in place along the side of  

the base. (Fig. 38)

FP1393

Fig. 38

  DVRTSB ceramic panels.

The logs can be identified by the number cast into 
their underside.
The logs must be correctly placed in the order 
described for the correct operation of the fireplace.

Refer to Figures 30 & 40 for log location and alignment.
1.  Unpack the logs from the shipping carton. 

Handle 

the logs carefully as they are fragile. 

2.  Remove front glass/frame assembly.
3.  Place the left rear (B105) and right rear (B106) 

logs in place on the grate. The square hole in the 
underside of the logs locates over the corner legs 
of the grate. The inner ends of the log point to the 
center of the burner.

4.  Place the left front (B107) and right front (B108) logs 

in place. Again the square holes fit over the corner 
legs of the grate. The inner ends of these logs have 
a recess in the underside which locates over knobs 
on the top of the B105 and B106 logs to lock the 
inner end in place.

5.  Place the center front (B109) log in place. The notch 

on the outer end of this log locates around the third 
outer prong on the grate and the inner ends with a 
round recess rest on lug on top of the left front log 
(B107).

6.  Place the center rear (B110) log in place. The square 

hole in the underside of this log, locates over the 
rear center bar of the grate. The inner end of the log 
having a rectangular recess rests on the rectangular 
knob on the end of the left front log, (B107). 

LG298

Fig. 39

  DVRTSB logs.

B105

B110

B106

B108

B109

B107

Содержание DVRTSB





































Отзывы: